Please wait a minute...
 
材料工程  2015, Vol. 43 Issue (6): 31-37    DOI: 10.11868/j.issn.1001-4381.2015.06.006
  材料与工艺 本期目录 | 过刊浏览 | 高级检索 |
Re及时效时间对耐腐蚀镍基定向合金组织和持久寿命的影响
杨海青1, 李青1, 肖程波1, 胡聘聘1, 林山峰2
1. 北京航空材料研究院 先进高温结构材料重点实验室, 北京 100095;
2. 中国人民解放军61267部队, 北京 101114
Effect of Re and Aging Time on Microstructure and Stress Rupture Life of Corrosion Resistance Directionally Solidified Ni-base Superalloy
YANG Hai-qing1, LI Qing1, XIAO Cheng-bo1, HU Pin-pin1, LIN Shan-feng2
1. Science and Technology on Advanced High Temperature Structural Materials Laboratory, Beijing Institute of Aeronautical Materials, Beijing 100095, China;
2. 61267 People's Liberation Army Troops, Beijing 101114, China
全文: PDF(3457 KB)  
输出: BibTeX | EndNote (RIS)      
摘要 优化设计了三种含Re分别为0%,2%,3%(质量分数)的耐腐蚀定向镍基高温合金,分析了三种合金在900℃高温时效过程中组织的变化,测试了三种合金在不同时效时间980℃/200MPa下的持久寿命。结果表明:随着Re含量和时效时间的增加,合金析出σ相的倾向增大,合金高温持久性能下降;Re明显细化持久性能试样的筏排结构,随着Re含量的增加,合金性能下降的幅度变小。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
杨海青
李青
肖程波
胡聘聘
林山峰
关键词 Re耐腐蚀合金高温时效组织持久寿命    
Abstract:Three corrosion resistance directionally solidified Ni-base superalloys with varying mass fraction of Re (0%, 2% and 3%, respectively) were optimally designed, microstructural evolution during high temperature aging at 900℃ was analyzed and the stress rupture life of three alloys was tested at 980℃/200MPa after different aging time. The results show that the tendency of σ phase precipitating grows and the high temperature rupture performance of the alloy decreases due to the increase of Re content and the aging time. The rafting structure of stress rupture specimen, which is obviously refined with the addition of Re, as Re content increases, the decrease of stress rupture performance becomes smaller.
Key wordsrhenium    corrosion resistance superalloy    high temperature aging    microstructure    stress rupture life
收稿日期: 2014-03-07     
1:  TG 142.2  
基金资助:国防基础科研项目(A0520133013);国家863计划(2012AA03A511)
通讯作者: 李青(1977-),女,高级工程师,主要研究方向为高温合金和精密铸造,联系地址:北京市81信箱1分箱(100095),E-mail:li.qing01@163.com     E-mail: li.qing01@163.com
引用本文:   
杨海青, 李青, 肖程波, 胡聘聘, 林山峰. Re及时效时间对耐腐蚀镍基定向合金组织和持久寿命的影响[J]. 材料工程, 2015, 43(6): 31-37.
YANG Hai-qing, LI Qing, XIAO Cheng-bo, HU Pin-pin, LIN Shan-feng. Effect of Re and Aging Time on Microstructure and Stress Rupture Life of Corrosion Resistance Directionally Solidified Ni-base Superalloy. Journal of Materials Engineering, 2015, 43(6): 31-37.
链接本文:  
http://jme.biam.ac.cn/jme/CN/10.11868/j.issn.1001-4381.2015.06.006      或      http://jme.biam.ac.cn/jme/CN/Y2015/V43/I6/31
[1] 郭建亭.高温合金材料学: 下册[M]. 北京: 科学技术出版社, 2010. GUO Jian-ting. Materials Science and Engineering for Superalloys: The Last of Three Volumes[M]. Beijing: Science and Technology Press, 2010.
[2] 骆宇时, 李嘉荣, 刘世忠, 等. Re对单晶高温合金高温高应力持久性能的影响[J]. 中国有色金属学报, 2005, 15(11): 1655-1659.LUO Yu-shi, LI Jia-rong, LIU Shi-zhong, et al. Effects of Re on stress rupture properties of single crystal superalloys at elevated temperature and high stress[J]. The Chinese Journal of Nonferrous Metals, 2005, 15(11): 1655-1659.
[3] 骆宇时, 李嘉荣, 刘世忠, 等. Re对单晶高温合金持久性能的强化作用[J]. 材料工程, 2005, (8): 10-14. LUO Yu-shi, LI Jia-rong, LIU Shi-zhong, et al. Strengthening effect of Re on stress rupture properties of single crystal superalloys[J]. Journal of Materials Engineering, 2005, (8): 10-14.
[4] 于今江, 李金国, 赵乃仁, 等. 铼对单晶高温合金DD32组织的影响[J]. 钢铁研究学报, 2003, 15(7): 253-256.YU Jin-jiang, LI Jin-guo, ZHAO Nai-ren, et al. Effect of rhenium on microstructure of single crystal superalloy DD32[J]. Journal of Iron and Steel Research, 2003, 15(7): 253-256.
[5] 骆宇时, 李嘉荣, 刘世忠, 等. 铼对单晶高温合金γ和γ'相的影响[J]. 钢铁研究学报, 2007, 19(6): 61-64.LUO Yu-shi, LI Jia-rong, LIU Shi-zhong, et al. Influence of rhenium on γ and γ' phase in single crystal superalloys[J]. Journal of Iron and Steel Research, 2007, 19(6): 61-64.
[6] BURGEL R, GROSSMANN J, L SEBRINK O, et al. Development of a new alloy for directional solidification of large industrial gas turbine blades[A]. Superalloys 2004[C]. Champion, PA: TMS, 2004.25-34.
[7] MURAKAMI H, HONMA T, KOIZUMI Y, et al. Distribution of platinum group metal in Ni-base single crystal superalloys[A]. Superalloys 2000[C]. Champion, PA: TMS, 2004. 747-756.
[8] CARON P. High γ' solvus new generation nickel-based superalloys for single crystal turbine blade applications[A]. Superalloys 2000[C]. Champion, PA: TMS, 2000. 737-746.
[9] REED R C, YEH A C, TIN S, et al. Identification of the partitioning characteristics of ruthenium in single crystal superalloys using atom probe tomography[J]. Scripta Materialia, 2004, 51(4): 327-331.
[10] WALSTON W S, SCAEFFER J C, MURPHY W H. A new type of microstructure instability in superalloy-SRZ[A]. Superalloys 1996[C]. Champion, PA: TMS, 1996: 9-17.
[11] POLLOCK T M, MUSHYPHY W H, GOLDMAN E H, et al. Grain defect formation during directional solidification of nickel base single crystals[A].Superalloys 1992[C]. Champion, PA: TMS, 1992.125-134.
[12] 杨海青, 李青, 肖程波, 等. Re对耐腐蚀镍基定向合金组织及持久寿命的影响[J]. 稀有金属, 2012, 36(4): 547-551. YANG Hai-qing, LI Qing, XIAO Cheng-bo, et al. Effect of Re on microstructure and stress-rupture life of corrosion resistant DS Ni-base superalloy[J]. Chinese Journal of Rare Metals, 2012, 36(4): 547-551.
[13] 蒋立武,李树索,邱自成,等. 拉晶速率对Ni3Al基单晶合金IC6SX凝固组织和高温持久性能的影响[J]. 金属学报, 2009, 45(5): 547-552. JIANG Li-wu,LI Shu-suo, QIU Zi-cheng,et al. Effect of withdrawal rate on microstructure and stress rupture properties of a Ni3Al-based single crystal superalloy IC6SX[J]. Acta Metallurgica Sinica, 2009, 45(5): 547-552.
[14] 王建涛, 骆合力, 李尚平, 等. 冷却速率对MX246A合金组织和持久性能的影响[J]. 铸造, 2010,59(4): 355-357. WANG Jian-tao, LUO He-li, LI Shang-ping,et al. Effect of cooling rate on microstructure and stress rupture property of MX246A alloy[J]. China Foundry,2010, 59(4): 355-357.
[15] 骆宇时,李嘉荣,刘世忠,等.Re对单晶高温合金蠕变过程中相定向粗化的影响[J]. 材料工程, 2006, (7): 43-50. LUO Yu-shi, LI Jia-rong, LIU Shi-zhong, et al. Effects of Re on γ' directional coarsening in single crystal superalloys during creep[J]. Journal of Materials Engineering, 2006, (7): 43-50.
[16] 管秀荣,刘恩泽,纪慧思,等.Re对一种新型镍基高温合金组织稳定性的影响[J].材料科学与工艺, 2012, 20(3): 94-98. GUAN Xiu-rong, LIU En-ze, JI Hui-si, et al. Effects of Re on microstructure stability in a new Ni-based superalloy[J]. Materials Science and Technology, 2012, 20(3): 94-98.
[17] 李唐,田素贵,夏丹,等.一种含Re镍基合金在高温时效期间的组织演化[J].稀有金属材料与工程, 2008, 37(11): 1925-1929. LI Tang, TIAN Su-gui, XIA Dan, et al. Microstructure evolution of a nickle-based superalloy contain Re during aging[J]. Rare Metal Materials and Engineering, 2008, 37(11): 1925-1929.
[18] 张宏炜. 长期时效对一种含Re定向凝固高温合金组织和性能的影响[J]. 航天制造技术, 2008,(8): 17-18. ZHANG Hong-wei. Effect of long-term aging on a kind of Re-containing directionally solidified superalloy in structure and property[J]. Aerospace Manufacturing Technology, 2008, (8): 17-18.
[1] 李小强, 敖敬培, 李子阳, 李力, 屈盛官. CuMnNiCo钎料钎焊MGH956合金接头组织及力学性能研究[J]. 材料工程, 2015, 43(5): 21-26.
[2] 卢棋, 何国球, 陈淑娟, 佘萌, 刘颺, 杨洋, 朱旻昊. 热机械训练过程中Fe-Mn-Si系形状记忆合金的组织演变[J]. 材料工程, 2015, 43(4): 8-12.
[3] 刘铭, 汝继刚, 臧金鑫, 张坤, 何维维, 王亮, 陈高红. 新型Al-Zn-Mg-Cu铝合金热稳定性研究[J]. 材料工程, 2015, 43(4): 13-18.
[4] 谭毅, 廖娇, 李佳艳, 石爽, 王清, 游小刚, 李鹏廷, 姜辛. 电子束熔炼Inconel740合金不同热处理状态下的组织演变与显微硬度[J]. 材料工程, 2015, 43(4): 19-24.
[5] 傅田, 李文亚, 杨夏炜, 李锦锋, 高大路. 搅拌摩擦点焊技术及其研究现状[J]. 材料工程, 2015, 43(4): 102-114.
[6] 彭建, 彭毅, 韩韡, 潘复生. 挤压温度对Mg-2Zn-Mn-0.5Nd镁合金组织和性能的影响[J]. 材料工程, 2015, 43(3): 23-27.
[7] 刘鹏, 李士凯, 张元彬, 刘燕. 非晶增强铝基复合材料的微观结构及腐蚀性能[J]. 材料工程, 2015, 43(3): 67-71.
[8] 杨闯, 彭晓东, 刘静, 马亚芹, 王华. TC4钛合金低压真空氮化改性层的制备与性能[J]. 材料工程, 2015, 43(3): 78-82.
[9] 雷玉成, 龚晨诚, 罗雅, 肖波, 朱强. 激励电流对MGH956合金原位合金化TIG焊接头性能的影响[J]. 材料工程, 2015, 43(2): 7-13.
[10] 谷晓鹏, 段珍珍, 邓钢, 谷晓燕. S355J2W+N钢激光-MAG复合焊与MAG焊对比[J]. 材料工程, 2015, 43(2): 20-25.
[11] 黄烁, 王磊, 张北江, 赵光普. GH4706合金的热变形行为与显微组织演化[J]. 材料工程, 2015, 43(2): 41-46.
[12] 冯广杰, 李卓然, 朱洪羽, 徐慨. SiC陶瓷真空钎焊接头显微组织和性能[J]. 材料工程, 2015, 43(1): 1-5.
[13] 刘胜明, 汤爱涛, 陈敏, 赵子鹏. 钛铁矿原位反应合成Al2O3-TiC颗粒增强铁基复合材料[J]. 材料工程, 2015, 43(1): 18-23.
[14] 闫世兴, 董世运, 徐滨士, 王玉江, 任维彬, 方金祥. 预热温度对灰铸铁表面激光熔覆镍基涂层组织与性能的影响[J]. 材料工程, 2015, 43(1): 30-36.
[15] 李万青, 魏红梅, 何鹏, 高丽娇, 林铁松, 李小强, 赫兰春. Ti3Al和Ti2AlNb合金扩散连接界面的组织及力学性能[J]. 材料工程, 2015, 43(1): 37-43.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
版权所有 © 2015《材料工程》编辑部
地址:北京81信箱44分箱 邮政编码: 100095
电话:010-62496276 E-mail:matereng@biam.ac.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn