Abstract:TC4 alloy samples were built by selective laser melting (SLM). The microstructure was observed, and electrochemical measurements were performed to investigate the corrosion resistance of SLMed TC4 alloy in different forming surface and roughness. The traditional rolled sample was introduced as a reference. Results show that processing method, forming surface and roughness act a significant role in influencing the corrosion resistance. The microstructure of SLMed TC4 on vertical section consists of the primitive columnar β grains filled with a large number of acicular α' martensites oriented at approximately ±45° with building direction. Unlike the typical α+β phase of traditional rolled sample, a chessboard pattern is observed on cross-section of SLMed TC4. The electrochemical results suggest that the corrosion resistance of traditional rolled sample is superior to that of SLMed sample. SLMed TC4 sample exhibits a better corrosion resistance on the vertical section, compared with the cross-section. Besides, the SLMed sample with rougher surface exhibits poorer corrosion resistance. Obvious etch pit is found on the surface of SLMed sample and the corrosion morphology is pitting.
[1] 蔡建明, 弭光宝,高帆,等.航空发动机用先进高温钛合金材料技术研究与发展[J].材料工程,2016,44(8):1-10. CAI J M,MI G B,GAO F,et al.Research and development of some advanced high temperature titanium alloys for aero-engine[J].Journal of Materials Engineering,2016,44(8):1-10.
[2] 连峰,臧路苹,项秋宽,等.超疏水钛合金表面在人工海水中的摩擦性能[J].金属学报,2016,52(5):592-598. LIAN F,ZANG L P,XIANG Q K,et al.Tribological performance of super hydro-phobic titanium alloy surface in artificial seawater[J].Acta Metallurgica Sinica,2016,52(5):592-598.
[3] 李春燕,寇生中,赵燕春,等.钛合金表面激光熔覆钴基合金层的组织及力学性能[J].材料热处理学报,2015,36(2):171-178. LI C Y,KOU S Z,ZHAO Y C,et al.Microstructure and mechanical property of laser clad Co-based alloy coatings on titanium alloy[J].Transactions of Materials and Heat Treatment,2015,36(2):171-178.
[4] PIAZZA S,BIUNDO G L,ROMANO M C,et al.In situ characterization of passive films on Al-Ti alloy by photocurrent and impedance spectroscopy[J].Corrosion Science,1998,40(7):1087-1108.
[5] 祝力伟,王新南,朱知寿.不同热处理工艺下TC4-DT钛合金的显微组织及力学性能[J].钛工业进展,2012,29(1):9-12. ZHU L W,WANG X N,ZHU Z S.Effect of heat treatment on microstructure and mechanical properties of TC4-DT alloy[J].Titanium Industry Progress,2012,29(1):9-12.
[6] IBRIS N,ROSCA J C M.EIS study of Ti and its alloys in biological media[J].Journal of Electroanalytical Chemistry,2002,526(1/2):53-62.
[7] HEAKAL E T,GHONEIM A A,MOGODA A S,et al.Electrochemical behaviour of Ti-6Al-4V alloy and Ti in azide and halide solutions[J].Corrosion Science,2011,53(9):2728-2737.
[8] ZAVERI N,MAHAPATRA M,DECEUSTER A,et al.Corrosion resistance of pulsed laser-treated Ti-6Al-4V implant in simulated biofluids[J].Electrochimica Acta,2008,53(15):5022-5032.
[9] RYAN G E,PANDIT A S,APATSIDIS D P.Porous titanium scaffolds fabricated using a rapid prototyping and powder metallurgy technique[J].Biomaterials,2008,29(27):3625-3635.
[10] BENEA L,MARDARE-DANAILA E,MARDARE M,et al.Preparation of titanium oxide and hydroxyapatite on Ti-6Al-4V alloy surface and electrochemical behaviour in bio-simulated fluid solution[J].Corrosion Science,2014,80:331-338.
[11] RAZAVI R S,SALEHI M,RAMAZANI M,et al.Corrosion behaviour of laser gas nitrided Ti-6Al-4V in HCl solution[J].Corrosion Science,2009,51(10):2324-2329.
[12] POHRELYUK I M,FEDIRKO V M,TKACHUK O V,et al.Corrosion resistance of Ti-6Al-4V alloy with nitride coatings in Ringer's solution[J].Corrosion Science,2013,66:392-398.
[13] VASTOLA G,ZHANG G,PEI Q X,et al.Modeling the microstructure evolution during additive manufacturing of Ti6Al4V:a comparison between electron beam melting and selective laser melting[J].JOM,2016,68(5):1370-1375.
[14] DANG K D,LI P F.The effect of laser energy input on the microstructure,physical and mechanical properties of Ti-6Al-4V alloys by selective laser melting[J].Virtual and Physical Prototyping,2016,11(1):41-47.
[15] DAI N W,ZHANG L C,ZHANG J X,et al.Corrosion behavior of selective laser melted Ti-6Al-4V alloy in NaCl solution[J].Corrosion Science,2016,102:484-489.
[16] YANG J J,YU H C,YIN J,et al.Formation and control of martensite in Ti-6Al-4V alloy produced by selective laser melting[J].Materials & Design,2016,108:308-318.
[17] VILARO T,COLIN C,BAETOUT J D.As-fabricated and heat-treated microstructures of the Ti-6Al-4V alloy processed by selective laser melting[J].Metallurgical and Materials Transactions A,2011,42(10):3190-3199.
[18] EDWARDS P,RAMULU M.Fatigue performance evaluation of selective laser melted Ti-6Al-4V[J].Materials Science and Engineering:A,2014,598:327-337.
[19] WEI K W,WANG Z M,ZENG X Y.Influence of element vaporization on formability,composition,microstructure,and mechanical performance of the selective laser melted Mg-Zn-Zr components[J].Materials Letters,2015,156:187-190.
[20] WANG Z M,GUAN K,GAO M,et al.The microstructure and mechanical properties of deposited-IN718 selective laser melting[J].Journal of Alloys & Compounds,2012,513:518-523.
[21] ATTAR H,BÖNISCH M,CALIN M,et al.Selective laser melting of in situ titanium-titanium boride composites:processing, microstructure and mechanical properties[J].Acta Materialia,2014,76:13-22.
[22] 彭立涛,王道明,邓子涛,等.表面粗糙度对锌涂层防腐性能的影响[J].全面腐蚀控制,2011,25(6):29-31. PENG L T,WANG D M,DENG Z T,et al.Influence of the surface roughness on the anticorrosion performance of Zn coating[J].Total Corrosion Control,2011,25(6):29-31.