Please wait a minute...
 
材料工程  2016, Vol. 44 Issue (9): 76-81    DOI: 10.11868/j.issn.1001-4381.2016.09.012
  材料与工艺 本期目录 | 过刊浏览 | 高级检索 |
中间退火对汽车用5182铝合金板组织和性能的影响
王宇1,2, 曹零勇1,2,3, 李俊鹏1,2, 张华1, 郭富安1,2
1 山东南山铝业股份有限公司 国家铝合金压力加工工程技术研究中心, 山东 龙口 265713;
2 北京南山航空材料研究院, 北京 100048;
3 中南大学 材料科学与工程学院, 长沙 410083
Effect of Intermediate Annealing on Microstructure and Property of 5182 Aluminum Alloy Sheet for Automobile
WANG Yu1,2, CAO Ling-yong1,2,3, LI Jun-peng1,2, ZHANG Hua1, GUO Fu-an1,2
1 National Engineering Research Center for Plastic Working of Aluminum Alloys, Shandong Nanshan Aluminum Co., Ltd., Longkou 265713, Shandong, China;
2 Beijing Nanshan Institute of Aeronautical Materials, Beijing 100048, China;
3 School of Materials Science and Engineering, Central South University, Changsha 410083, China
全文: PDF(23940 KB)   HTML()
输出: BibTeX | EndNote (RIS)      
摘要 采用光学显微镜、扫描电子显微镜、万能力学试验机等测试分析手段,研究中间退火对5182铝合金完全退火态(5182-O)板材组织和性能的影响。结果表明:与未经中间退火的5182-O板材相比,中间退火后的5182-O板材晶粒尺寸过于细小,金属间化合物破碎不充分、尺寸大,弥散析出相数量少;屈服强度、抗拉强度、加工硬化指数和塑性应变比厚向各向异性降低,塑性应变比平面各向异性增大;板材的组织、力学性能和成形性能未获得有效改善和提高。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
王宇
曹零勇
李俊鹏
张华
郭富安
关键词 中间退火铝合金显微组织力学性能成形性能    
Abstract:Effect of intermediate annealing on the microstructure and properties of 5182 aluminum alloy sheet with full annealed state (5182-O) was investigated by means of optical microscope, scanning electron microscope and universal testing machine. The results indicate that compared with 5182-O sheet without intermediate annealing, 5182-O sheet with intermediate annealing possesses too fine grain size, intermetallic compounds not broken enough, larger size intermetallic particles, less dispersed phase. Yield strength and ultimate tensile strength, work hardening exponent and normal anisotropy of plastic strain ratio decrease but planner anisotropy of plastic strain ratio increases. The mechanical properties and forming ability of 5182-O aluminum alloy sheet and its microstructure are not improved significantly after intermediate annealing.
Key wordsintermediate annealing    aluminium alloy    microstructure    mechanical property    forming ability
收稿日期: 2014-12-01      出版日期: 2016-09-27
中图分类号:  TG146.2+1  
通讯作者: 曹零勇(1984-),男,博士,从事汽车用高性能铝合金板材研究,联系地址:北京市海淀区车公庄西路19号外文文化创意园8号楼三层(100048),E-mail:lingyongcao@163.com     E-mail: lingyongcao@163.com
引用本文:   
王宇, 曹零勇, 李俊鹏, 张华, 郭富安. 中间退火对汽车用5182铝合金板组织和性能的影响[J]. 材料工程, 2016, 44(9): 76-81.
WANG Yu, CAO Ling-yong, LI Jun-peng, ZHANG Hua, GUO Fu-an. Effect of Intermediate Annealing on Microstructure and Property of 5182 Aluminum Alloy Sheet for Automobile. Journal of Materials Engineering, 2016, 44(9): 76-81.
链接本文:  
http://jme.biam.ac.cn/CN/10.11868/j.issn.1001-4381.2016.09.012      或      http://jme.biam.ac.cn/CN/Y2016/V44/I9/76
[1] MILLR W S,ZHUANG L,BOTTEMA J,et al.Recent development in aluminum alloys for the automotive industry[J].Materials Science and Engineering:A,2000,280(1):37-49.
[2] 王孟君,黄电源,姜海涛.汽车用铝合金的研究进展[J].金属热处理,2006,31(9):35-39.WANG M J,HUANG D Y,JIANG H T.Research progress of aluminum alloys for the automotive industry[J].Heat Treatment of Metals,2006,31(9):35-39.
[3] RATCHEVAY P,VERLINDEN B,Van HOUTTEA P,et al.Hot ductility of an Al-4wt.% Mg-0.5wt.% Cu alloy[J].Materials Science and Engineering:A,1997,222(2):189-196.
[4] LI S Y,KANG S B,KO H S.Effect of intermediate annealing on texture evolution and plastic anisotropy in an Al-Mg auto-body alloy[J].Metallurgical and Materials Transactions A,2000,31(1):99-107.
[5] NURGER G B,GUPTA A K,TEFFERY P W,et al.Microstructural control of aluminum sheet used in automotive applications[J].Materials Characterization,1995,35(1):23-39.
[6] LI S Y,KANG S B,KO H S.Texture and plastic anisotropy of Al-Mg-0.3Cu-1.0Zn alloys[J].Scripta Materialia,1997,37(4):411-417.
[7] LI Y J,ZHANG W Z,MARTHINSEN K.Precipitation crystallography of plate-shaped Al6(Mn,Fe) dispersoids in AA5182 alloy[J].Acta Materialia,2012,60(17):5963-5974.
[8] WEN W,MORRIS J G.The effect of cold rolling and annealing on the serrated yielding phenomenon of AA5182 aluminum alloy[J].Materials Science and Engineering:A,2004,373(1-2):204-216.
[9] 王孟君,黄电源,姜海涛,等.退火对汽车用5182铝合金板材组织与性能的影响[J].金属热处理,2007,32(9):18-20.WANG M J,HUANG D Y,JIANG H T,et al.Influence of annealing process on microstructure and properties of 5182 aluminum alloy sheet for automobile[J].Heat Treatment of Metals,2007,32(9):18-20.
[10] 高家诚,陈志强,明文良.中间退火工艺对5182铝合金带材性能的影响[J].材料热处理学报,2009,30(3):146-149.GAO J C,CHEN Z Q,MING W L.Effects of annealing process on properties of 5182 aluminum alloy strips[J].Transactions of Materials and Heat Treatment,2009,30(3):146-149.
[11] LIU W C,MORRIS J G.Effect of pre-treatment on recrystallization and recrystallization textures of cold rolled CC AA 5182 aluminum alloy[J].Materials Science and Engineering:A,2003,363(1-2):253-262.
[12] 胡赓祥,蔡珣,戎咏华.材料科学基础[M].上海:上海交通大学出版社,2006.66-68.HU G X,CAI X,RONG Y H.Fundamentals of Materials Science[M].Shanghai:Shanghai Jiao Tong University Press,2006.66-68.
[13] 舒龙卫,毛卫民,冯惠平,等.冷轧低压电子铝箔退火加热过程中的再结晶和晶粒长大[J].中国有色金属学报,2002,12(增刊1):178-182.SHU L W,MAO W M,FENG H P,et al.Recrystallization and grain growth during annealing of cold rolled low voltage electronic aluminum foil[J].The Chinese Journal of Nonferrous Metals,2002,12(Suppl 1):178-182.
[14] FORTES M A.Constitutive equations for inhomogeneous plastic flow and application to Luder's band propagation[J].Journal of Materials Science,1984,19(5):1496-1504.
[15] MOULIN N,PARRA-DENIS E,JEULIN D,et al.Constituent particle break-up during hot rolling of AA 5182[J].Advanced Engineering Materials,2010,12(1-2):20-29.
[16] HAMERTON R,CAMA H,MEREDITH M W.Development of the coarse intermetallic particle population in wrought aluminum alloys during ingot casting and thermo-mechanical processing[J].Materials Science Forum,2000,331-337:143-154.
[17] LLOYD D J,COURT S A.Influence of grain size on tensile properties of Al-Mg alloys[J].Materials Science and Technology,2003,19(10):1349-1354.
[18] CHOI S H,CHOI J K,KIM H W,et al.Effect of reduction ratio on annealing texture and r-value directionality for a cold-rolled Al-5% Mg alloy[J].Materials Science and Engineering:A,2009,519(1-2):77-87.
[1] 李小强, 肖晴, 李力, 屈盛官. Al-Si-Cu-Zn钎料钎焊3003铝合金的接头组织及力学性能[J]. 材料工程, 2016, 44(9): 32-37.
[2] 任魏巍, 邹林池, 张兴峰, 符殿宝, 陈俊锋. 7050铝合金时效成形中应力松弛行为与回弹方程[J]. 材料工程, 2016, 44(9): 89-95.
[3] 洪起虎, 燕绍九, 杨程, 张晓艳, 戴圣龙. 氧化石墨烯/铜基复合材料的微观结构及力学性能[J]. 材料工程, 2016, 44(9): 1-7.
[4] 徐学宏, 王小群, 闫超, 王旭. 环氧树脂及其复合材料微波固化研究进展[J]. 材料工程, 2016, 44(8): 111-120.
[5] 万响亮, 李光强, 周博文, 马江华. 奥氏体不锈钢晶粒细化对形变机制和力学性能的影响[J]. 材料工程, 2016, 44(8): 29-33.
[6] 王丙兴, 董福志, 王昭东, 王国栋. 超快冷条件下Mn-Nb-B系低碳贝氏体高强钢组织与性能研究[J]. 材料工程, 2016, 44(7): 26-31.
[7] 庞启航, 唐荻, 赵征志, 武会宾, 李烁. 低活化钢析出相热力学研究[J]. 材料工程, 2016, 44(7): 37-42.
[8] 刘慧丛, 李峰, 张建周, 姬振江, 王萌, 朱立群. 硅溶胶对LY12CZ铝合金硼硫酸阳极氧化的影响[J]. 材料工程, 2016, 44(7): 49-53.
[9] 潘健, 肖长发, 赵健, 黄庆林, 任倩. 单轴取向乙烯-三氟氯乙烯共聚物纤维结晶结构与性能表征[J]. 材料工程, 2016, 44(7): 73-77.
[10] 张鉴炜, 石刚, 江大志. Buckypaper/环氧复合材料加压滤渗浸渍法制备工艺研究[J]. 材料工程, 2016, 44(7): 1-6.
[11] 曹宇, 刘荣军, 曹英斌, 龙宪海, 严春雷, 张长瑞. 素坯密度对气相渗硅制备C/C-SiC复合材料结构与性能的影响[J]. 材料工程, 2016, 44(7): 19-25.
[12] 郝亚鑫, 王文, 徐瑞琦, 乔柯, 李天麒, 王快社. 焊后热处理对7A04铝合金水下搅拌摩擦焊接接头组织性能的影响[J]. 材料工程, 2016, 44(6): 70-75.
[13] 付超, 冯微, 童锦艳, 郑运荣, 冯强. GH4033涡轮叶片服役1600h后的显微组织及力学性能评价[J]. 材料工程, 2016, 44(6): 84-91.
[14] 秦仁耀, 孙兵兵, 肇恒跃, 郭绍庆, 唐思熠, 张学军. ZM5镁合金TIG焊接接头组织与力学性能[J]. 材料工程, 2016, 44(6): 92-97.
[15] 黄正华, 刘汪涵博, 戚文军, 徐静. 第三组元对Mg-Sn合金铸态组织与力学性能的影响[J]. 材料工程, 2016, 44(6): 56-62.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
版权所有 © 2015《材料工程》编辑部       总访问数: 
地址:北京81信箱44分箱 邮政编码: 100095
电话:010-62496276 E-mail:matereng@biam.ac.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn