Please wait a minute...
 
材料工程  2013, Vol. 0 Issue (4): 1-5,11    DOI: 10.3969/j.issn.1001-4381.2013.04.001
  材料与工艺 本期目录 | 过刊浏览 | 高级检索 |
冷喷涂制备颗粒增强钛基复合材料涂层研究
黄春杰1, 李文亚1, 余敏1,2, 廖汉林2
1. 西北工业大学 凝固技术国家重点实验室,西安 710072;
2. 贝尔福-蒙贝利亚尔技术大学LERMPS实验室,法国 贝尔福 90010
Investigation on Particles Reinforced Titanium Matrix Composite Coating Fabricated by Cold Spraying
HUANG Chun-jie1, LI Wen-ya1, YU Min1,2, LIAO Han-lin2
1. State Key Laboratory of Solidification Processing,Northwestern Polytechnical University, Xi’an 710072,China;
2. Laboratory for Study and Research into Materials,Processes and Surfaces,Technical University Belfort Montbeliard,Belfort 90010,France
全文: PDF(2076 KB)   HTML()
输出: BibTeX | EndNote (RIS)      
摘要 以Ti粉为复合材料基体相,不规则的SiC粉为增强相,采用冷喷涂技术制备了SiC颗粒增强钛基复合材料涂层,研究了硬质相对复合涂层的显微组织和显微硬度的影响。结果表明:制备的复合涂层由两个明显的区域组成:表层的多孔区和内部的致密区,随距离涂层表面深度的增加,涂层的气孔率迅速下降;原始喷涂粉末中SiC的体积分数为30%,沉积后的复合涂层中SiC体积分数约为10%;此外,增强相SiC颗粒的加入不仅可有效地降低涂层的气孔率,还显著地提高了喷涂态涂层的显微硬度值,由(72±28)HV0.1提高至(125±17.75)HV0.3
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
黄春杰
李文亚
余敏
廖汉林
关键词 冷喷涂PRTMCSiC显微组织显微硬度    
Abstract:SiC particles reinforced Ti matrix composite(PRTMC) was prepared by cold spraying,using titanium metallic matrix blended with reinforcement of irregular SiC powder as feedstock. The effect of SiC reinforcement on the microstructure and microhardness of the composite coating was studied. The results show that two distinguishable regions exist in the deposited composite coating: the outer region and the inner region. The outer region presents a porous microstructure, while the inner region has a dense microstructure. The porosity of the coating becomes smaller with the increasing of the depth from the surface towards the boundary. The volume fraction of SiC particles in the deposited coating is 10% compared to that of 30% in the feedstock. Furthermore, the addition of SiC particles can effectively reduce the coating porosity, and greatly increases the microhardness of cold-sprayed coating from (72?28)HV0.1 to (125?17.75)HV0.3.
Key wordscold spraying    PRTMC    SiC    microstructure    microhardness
收稿日期: 2012-10-15      出版日期: 2013-04-20
1:  TB331  
  TG174.442  
基金资助:

国家自然科学基金资助项目(51005180);霍英东教育基金青年教师基金资助(131052);"111"引智计划资助(B08040)

通讯作者: 李文亚(1976-),男,教授,博士,主要从事摩擦焊及热喷涂技术的研究,联系地址:陕西省西安市友谊西路127号西北工业大学材料学院公字楼413室(710072)     E-mail: liwy@nwpu.edu.cn
作者简介: 黄春杰(1988-),男,硕士研究生,主要从事冷喷涂和摩擦焊技术的研究,E-mail:hcj@mail.nwpu.edu.cn
引用本文:   
黄春杰, 李文亚, 余敏, 廖汉林. 冷喷涂制备颗粒增强钛基复合材料涂层研究[J]. 材料工程, 2013, 0(4): 1-5,11.
HUANG Chun-jie, LI Wen-ya, YU Min, LIAO Han-lin. Investigation on Particles Reinforced Titanium Matrix Composite Coating Fabricated by Cold Spraying. Journal of Materials Engineering, 2013, 0(4): 1-5,11.
链接本文:  
http://jme.biam.ac.cn/CN/10.3969/j.issn.1001-4381.2013.04.001      或      http://jme.biam.ac.cn/CN/Y2013/V0/I4/1
[1] MAO X N, ZHOU L, ZHOU Y G, et al. Characteristic of principle properties and microstructure of TP-650 particles reinforced titanium matrix composites[J].Rare Metal Mat Eng,2004,33(6):620-623.
[2] BAO G, LIN Z. High strain rate deformation in particle reinforced metal matrix composites[J].Acta Mater,1996,44(3):1011-1019.
[3] 张和善.国外航空结构材料发展概况——先进复合材料(II)[J].航空制造工程,1998,(1):12-14.
[4] SANDHU S, TSAKIROPOULOS P, WOOD M J, et al. Interfacial studies in titanium aluminide/SiC composites[J].Key Eng Mater,1997,127-131:671-678.
[5] 刘大响.航空发动机技术的发展和建议[J].中国工程科学,1999,(2):24-29.LIU D X. The development and proposals of the aeroengine technology[J].Eng Sci,1999,(2):24-29.
[6] 毛小南,于兰兰.非连续增强钛基复合材料研究新进展[J].中国材料进展,2010,29(5):18-24.MAO X N,YU L L. New development in research of discontinuously reinforced titanium matrix composites[J].Mater China, 2010,29(5):18-24.
[7] 吕维洁.原位自生钛基复合材料研究综述[J].中国材料进展,2010,29(4):41-48.LU W J. An overview on the research of in-situ titanium matrix composites[J].Mater China,2010,29(4):41-48.
[8] PAPYRIN A. Cold spray technology[J].Adv Mater Process,2001,159(9):49-51.
[9] LI W Y, LIAO H L, WANG H T. Cold spraying of light alloys. DONG H. Surface Engineering of Light Alloys-Al, Mg and Ti Alloys.UK: Woodhead Publishing,2010.242-293.
[10] BLOSE R E, WALKER B H, WALKER R M, et al. New opportunities to use cold spray process for applying additive features to titanium alloys[J].Met Powder Rep,2006,61(9):30-37.
[11] WONG W, IRISSOU E, RYABININ A N, et al. Influence of helium and nitrogen gases on the properties of cold gas dynamic sprayed pure titanium coatings[J].J Therm Spray Techn,2011,20(1-2):213-226.
[12] ZAHIRI S H, ANTONIO C I, JAHEDI M. Elimination of porosity in directly fabricated titanium via cold gas dynamic spraying[J].J Mater Process Tech,2009,209(2):922-929.
[13] BINDER K, GRTNER F, KLASSEN T. Cold spraying of titanium using enhanced conditions and optimized nozzles.Thermal Spray 2011:Proceeding of the International Thermal Spray Conference.Düsseldorf: DVS Media GmbH,2011.879-884.
[14] IRISSOU E, LEGOUX J G, ARSENAULT B, et al. Investigation of Al-Al2O3 cold spray coating formation and properties[J].J Therm Spray Techn,2007,16(5-6):661-668.
[15] TAO Y S, XIONG T Y, SUN C, et al. Effect of α-Al2O3 on the properties of cold sprayed Al/α-Al2O3 composite coatings on AZ91D magnesium alloy[J].Appl Surf Sci,2009,256(1):261-266.
[16] LI W Y, ZHANG G, GUO X P, et al. Characterizations of cold-sprayed TiN particle-reinforced Al alloy-based composites—from structures to tribological behaviour[J].Adv Eng Mater,2007,9(7):577-583.
[17] LI W Y, ZHANG G, ZHANG C, et al. Effect of ball milling of feedstock powder on microstructure and properties of TiN particle-reinforced Al alloy-based composites fabricated by cold spraying[J].J Therm Spray Techn,2008,17(3):316-322.
[18] 王锋,漆波,陈清华,等.超音速冷喷涂Cu-Al2O3复合涂层特性[J].材料导报,2009,23(6):47-50. WANG F, QI B, CHEN Q H, et al. Properties of Cu-Al2O3 composite coating in supersonic cold gas dynamic spraying[J].Mat Rev,2009,23(6):47-50.
[19] 所新坤,杨冠军,李长久.镍基金刚石复合涂层的冷喷涂制备[J].材料研究与应用,2009,3(1):32-36. SUO X K, YANG G J, LI C J. Preparation of Ni-based alloy diamond composite coatings by cold spray[J].Mate Res Appl, 2009,3(1):32-36.
[20] SANSOUCY E, MARCOUX P, AJDELSZTAJN L, et al. Properties of SiC-reinforced aluminum alloy coatings produced by the cold gas dynamic spraying process[J].Surf Coat Tech,2008,202(16):3988-3996.
[21] SPENCER K, FABIJANIC D M, ZHANG M X. The use of Al-Al2O3 cold spray coatings to improve the surface properties of magnesium alloys[J].Surf Coat Tech,2009,204:336-344.
[22] SHEN L, KONG L Y, XIONG T Y, et al. Preparation of TiAl3-Al composite coating by cold spraying[J].Trans Nonferrous Met Soc China,2009,19(4):879-882.
[23] LI C J, LI W Y. Deposition characteristics of titanium coating in cold spraying[J]. Surf Coat Tech,2003,167(2-3):278-283.
[24] BLOSE R E. Spray forming titanium alloys using the cold spray process.LUGSCHEIDER E. Thermal Spray Connects:Explore its Surfacing Potential.Düsseldorf:DVS,2005.
[25] LI W Y, ZHANG C, WANG H T, et al. Significant influences of metal reactivity and oxide film of powder particles on coating deposition characteristics in cold spraying[J].Appl Surf Sci, 2007,253(7):3557-3562.
[26] YU M, LI W Y, SUO X K, et al. Effect of ceramic particles size on the microstructure and properties of cold sprayed Al5056/SiCp composite coatings.Thermal Spray 2012:Proceedings from the International Thermal Spray Conference and Exposition.Ohio:ASM International,2012.298-304.
[27] MatWeb for Property Information, http://www.matweb.com (accessed May14,2007).
[28] LI W Y, ZHANG C, LIAO H, et al. Effect of heat treatment on microstructure and mechanical properties of cold sprayed Ti coatings with relatively large powder particles[J].J Coat Technol Res,2009,6(3):401-406.
[29] OH J C, YUN E, GOLKOVSKI M G, et al. Improvement of hardness and wear resistance in SiC/Ti-6Al-4V surface composites fabricated by high-energy electron beam irradiation[J].Mat Sci Eng:A,2003,351(1-2):98-108.
[30] AJAJA J, GOLDBAUM D, CHROMIK R R. Characterization of Ti cold spray coatings by indentation methods[J].Acta Astronaut,2011,69(11-12):923-928.
[1] 许天旱, 冯耀荣. III型载荷分量对不同显微组织套管钻井用钢断裂韧性的影响[J]. 材料工程, 2015, 43(9): 66-73.
[2] 何正林, 高文理, 陆政, 冯朝辉. 热处理对7A85铝合金组织和性能的影响[J]. 材料工程, 2015, 43(8): 13-18.
[3] 谭毅, 廖娇, 李佳艳, 石爽, 王清, 游小刚, 李鹏廷, 姜辛. 电子束熔炼Inconel740合金不同热处理状态下的组织演变与显微硬度[J]. 材料工程, 2015, 43(4): 19-24.
[4] 马彦, 陈朝辉. 1800℃热处理对PIP法C/SiC复合材料结构和性能的影响[J]. 材料工程, 2015, 43(4): 98-101.
[5] 张响, 陈招科, 熊翔. C/C-SiC复合材料表面ZrB2基陶瓷涂层的制备及高温烧结机理[J]. 材料工程, 2015, 43(3): 1-6.
[6] 王兵, 谭毅, 施伟, 李佳艳, 尤启凡. 硅蒸镀法制备低密度C/C复合材料表面SiC涂层[J]. 材料工程, 2015, 43(2): 1-6.
[7] 雷玉成, 龚晨诚, 罗雅, 肖波, 朱强. 激励电流对MGH956合金原位合金化TIG焊接头性能的影响[J]. 材料工程, 2015, 43(2): 7-13.
[8] 石仲川, 张晓云, 陈昊, 丁方正, 宇波, 汤智慧, 陆峰. 高强钢冷喷涂铝锌复合涂层性能研究[J]. 材料工程, 2015, 43(2): 14-19.
[9] 赵东阳, 刘伟, 沙江波. 放电等离子烧结制备Nb-Si-Ti-Al-Hf-Cr合金的显微组织及力学性能[J]. 材料工程, 2015, 43(10): 20-27.
[10] 王红星, 谈淑咏, 柳秉毅, 沈彤. 纳米SiC浓度对Ni/纳米MoS2基复合镀层结构和耐磨性能的影响[J]. 材料工程, 2015, 43(10): 60-65.
[11] 冯广杰, 李卓然, 朱洪羽, 徐慨. SiC陶瓷真空钎焊接头显微组织和性能[J]. 材料工程, 2015, 43(1): 1-5.
[12] 杜红燕, 李亚江. AZ31/7005异种材料填丝GTAW焊接接头的组织与性能[J]. 材料工程, 2014, 0(9): 14-19.
[13] 邵长斌, 熊江涛, 孙福, 张赋升, 李京龙. TC4钛合金与YG8硬质合金高频感应钎焊组织及性能研究[J]. 材料工程, 2014, 0(9): 26-31.
[14] 张盼, 叶凌英, 顾刚, 蒋海春, 张新明. 5A90铝锂合金超塑性变形的组织演变及变形机理[J]. 材料工程, 2014, 0(9): 51-56.
[15] 王智慧, 万国力, 贺定勇, 蒋建敏, 崔丽. Fe-Cr-B-C堆焊合金的组织与耐磨性[J]. 材料工程, 2014, 0(9): 57-62.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
版权所有 © 2015《材料工程》编辑部
地址:北京81信箱44分箱 邮政编码: 100095
电话:010-62496276 E-mail:matereng@biam.ac.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn