Please wait a minute...
 
材料工程  2013, Vol. 0 Issue (3): 38-41,50    DOI: 10.3969/j.issn.1001-4381.2013.03.008
  材料与工艺 本期目录 | 过刊浏览 | 高级检索 |
异步累积叠轧纯铜材的取向变化过程与力学性能
周蕾1, 史庆南1, 王军丽2, 米辉1, 刘润1
1. 昆明理工大学 材料科学与工程学院,昆明 650093;
2. 昆明理工大学 分析测试研究中心,昆明 650093
Texture and Mechanical Properties of Pure Copper Deformed by Asymmetrical Accumulative Roll-bonding
ZHOU Lei1, SHI Qing-nan1, WANG Jun-li2, MI Hui1, LIU Run1
1. Faculty of Material Science and Engineering, Kunming University of Science & Technology, Kunming 650093, China;
2. Research Center for Analysis and Measurement, Kunming University of Science and Technology, Kunming 650093, China
全文: PDF(2971 KB)   HTML()
输出: BibTeX | EndNote (RIS)      
摘要 室温下对纯铜薄板进行一到六道次的异步累积叠轧变形加工。采用金相显微镜、扫描电镜附带背散射电子衍射、X射线衍射仪附带织构附件及拉伸试验机进行组织、取向观察及力学性能测试,获得铜材异步叠轧过程的显微组织、轧制织构变化过程和力学性能。结果表明:经过六道次的异步累积叠轧变形,由于压缩变形与剪切变形作用,使晶粒细化,铜材晶粒尺寸由30~50μm细化到5μm。异步叠轧过程中出现:{112}〈111〉,{123}〈634〉,{011}〈211〉和{011}〈100〉几种主要组分轧制织构。材料的屈服强度与抗拉强度明显提高,六道次后分别达到348MPa和452MPa。材料的伸长率在二道次后显著下降到2.3%,然后随等效应变的增加略微下降。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
周蕾
史庆南
王军丽
米辉
刘润
关键词 纯铜异步叠轧显微组织织构力学性能    
Abstract:Pure copper sheets were prepared by Asymmetrical Accumulative Rolling Bonding(AARB) at room temperature. By optical microscopy, scanning electron microscopy(SEM) with electron backscattered diffraction(EBSD),X-ray diffractometer(XRD) with texture accessories and stretch mechanics performance tests, the microstructure,texture and mechanical properties of pure copper sheets by AARB were discussed. The results show that after six times of AARB, the grains of copper is refined by compression deformation and shearing deformation ,and the average grain size is refined to 5μm. Texture of sample main composed of {112}〈111〉, {123}〈634〉,{011}〈211〉 and {011}〈100〉. Yield strength and tensile strength of sample increase obviously.σ0.2 and σb got to 348MPa and 452MPa separately. The elongation of sample decreases to 2.3% after the second pass, and then it decreases a little with the rise of the equivalent strain.
Key wordspure copper    asymmetrical accumulative roll-bonding    microstructure    texture    mechanical properties
收稿日期: 2012-03-21      出版日期: 2013-03-20
中图分类号: 

TG335.5

 
  TG339

 
基金资助:

国家自然科学基金(50804018);稀贵及有色金属先进材料教育部重点实验室开放基金(ZDS2010015C);2010云南省科技条件平台建设计划(2010DH025)

通讯作者: 王军丽,教授,博士,联系地址:昆明理工大学分析测试研究中心(650093)     E-mail: junliwangli@yahoo.com.cn
作者简介: 周蕾(1987—),女,博士,主要从事材料加工及新材料制备方向的研究,E-mail:zhoulei7166@126.com
引用本文:   
周蕾, 史庆南, 王军丽, 米辉, 刘润. 异步累积叠轧纯铜材的取向变化过程与力学性能[J]. 材料工程, 2013, 0(3): 38-41,50.
ZHOU Lei, SHI Qing-nan, WANG Jun-li, MI Hui, LIU Run. Texture and Mechanical Properties of Pure Copper Deformed by Asymmetrical Accumulative Roll-bonding. Journal of Materials Engineering, 2013, 0(3): 38-41,50.
链接本文:  
http://jme.biam.ac.cn/CN/10.3969/j.issn.1001-4381.2013.03.008      或      http://jme.biam.ac.cn/CN/Y2013/V0/I3/38
[1] SAITO Y,UTAUNOMIYA H,TSUJI N,et al. Novel ultrahigh straining process for bulk materials: development of the accumulative roll-bonding process [J]. Acta Mater,1999,47(2):579-583.
[2] SAITO Y,TSUJI N,UTAUNOMIYA H,et al. Ultra-fine grained bulk aluminum produced by accumulative roll-bonding process[J]. Scripta Mater,1998,39(9):122-1227.
[3] JANG Y H,KIM S S,HAN S N,et al. Effect of trace phosphorous on tensile behavior of accumulative roll boned oxygen-free copper[J]. Scripta Mater,2005,52(1):21-24.
[4] PEREZ-PRADO M T,DEL V J A,RUANO O A. Grain refinement of Mg-Al-Zn alloys via accumulative roll bonding[J]. Sricpta Mater,2004,51(11):1093-1097.
[5] 王军丽, 史庆南, 王效琪.异步累积叠轧技术制备超细晶铜材退火过程组织及取向研究[J].材料工程,2008,(11):5-8.WANG Jun-li,SHI Qing-nan,WANG Xiao-qi. Study on microstructure and orientation evolution of ultra-fine grained copper prepared by asymmetrical accumulative rolling bonding (AARB)during annealing[J]. Journal of Materials Engineering,2008,(11):5-8.
[6] KIM W J,LEE J B,KIM W Y,et al. Microstructure and mechanical properties of Mg-Al-Zn alloy sheets severely deformed by asymmetrical rolling[J]. Scripta Mater,2007,56(4): 309-312.
[7] 杨德庄. 位错与金属强化机制[M]. 哈尔滨:哈尔滨工业大学出版社,1991.
[8] 运新兵, 宋宝韫, 陈莉.连续等径角挤压制备超细晶铜[J]. 中国有色金属学报,2006,16(9): 1563—1569.YUN Xin-bing,SONG Bao-yun,CHEN Li. Ultra-fine grain copper prepared by continuous equal channel angular press[J]. The Chinese Journal of Nonferrous Metals,2006,16(9):1563-1569.
[9] 张继东,李才巨,朱心昆,等. 大塑性变形对纯铜力学性能的影响[J]. 云南冶金,2007,36(1):56-58.ZHANG Ji-dong,LI Cai-ju,ZHU Xin-kun,et al. Effect of severe plastic deformation(SPD) on the mechanical properties of pure Cu[J]. Yunnan Metallurgy, 2007,36(1): 56-58.
[10] DAO M,LU L,SHEN Y F,et al. Strength, strain-rate sensitivity and ductility of copper with nanoscale twins[J]. Acta Materialia, 2006,54(20): 5421-5432.
[11] ZHANG Y G, LU J, ZHANG H W, et al. Strengthening and toughening by interface-mediated slip transfer reaction in nanotwinned copper[J]. Scripta Materialia, 2009,60(7): 508-511.
[12] ZHANG Y, TAO N R,LU K. Mechanical properties and rolling behaviors of nano-grained copper with embedded nano-twin bundles[J]. Acta Materialia, 2008,56(11): 2429-2440.
[1] 赵云松, 张迈, 郭小童, 郭媛媛, 赵昊, 刘砚飞, 姜华, 张剑, 骆宇时. 航空发动机涡轮叶片超温服役损伤的研究进展[J]. 材料工程, 2020, 48(9): 24-33.
[2] 段晓鸽, 江海涛, 米振莉, 王丽丽, 李萧. 轧制方式对6016铝合金薄板组织和塑性各向异性的影响[J]. 材料工程, 2020, 48(8): 134-141.
[3] 许凤光, 刘垚, 马文江, 张憬. 退火工艺对Zn/AZ31/Zn复合板材界面微观结构及力学性能的影响[J]. 材料工程, 2020, 48(8): 142-148.
[4] 郝思嘉, 李哲灵, 任志东, 田俊鹏, 时双强, 邢悦, 杨程. 拉曼光谱在石墨烯聚合物纳米复合材料中的应用[J]. 材料工程, 2020, 48(7): 45-60.
[5] 唐大秀, 刘金云, 王玉欣, 尚杰, 刘钢, 刘宜伟, 张辉, 陈清明, 刘翔, 李润伟. 柔性阻变存储器材料研究进展[J]. 材料工程, 2020, 48(7): 81-92.
[6] 张梦清, 于鹤龙, 王红美, 尹艳丽, 魏敏, 乔玉林, 张伟, 徐滨士. 感应熔覆原位合成TiB增强钛基复合涂层的微结构与力学性能[J]. 材料工程, 2020, 48(7): 111-118.
[7] 冯景鹏, 余欢, 徐志锋, 蔡长春, 王振军, 胡银生, 王雅娜. 2.5D浅交直联Cf/Al复合材料的显微组织及弯曲和剪切性能[J]. 材料工程, 2020, 48(6): 132-139.
[8] 李和奇, 王晓民, 曾宏燕. 热处理对FeCrMnNiCox合金微观组织及力学性能的影响[J]. 材料工程, 2020, 48(6): 170-175.
[9] 赵辉, 赵菲, 杨长龙, 韩钰, 靳东, 李红英. 时效处理对Al-Zr-Sc(-Er)合金组织和性能的影响[J]. 材料工程, 2020, 48(5): 112-119.
[10] 李淑文, 赵孔银, 陈康, 李金刚, 赵磊, 王晓磊, 魏俊富. TiO2共混丝朊接枝聚丙烯腈过滤膜制备及性能研究[J]. 材料工程, 2020, 48(3): 47-52.
[11] 赵新龙, 金鑫, 丁成成, 俞娟, 王晓东, 黄培. 热处理时间对聚甲基丙烯酰亚胺(PMI)泡沫结构和性能的影响[J]. 材料工程, 2020, 48(3): 53-58.
[12] 叶寒, 黄俊强, 张坚强, 李聪聪, 刘勇. 纳米WC增强选区激光熔化AlSi10Mg显微组织与力学性能[J]. 材料工程, 2020, 48(3): 75-83.
[13] 姚小飞, 田伟, 李楠, 王萍, 吕煜坤. 铜导线表面热浸镀PbSn合金镀层的组织与性能[J]. 材料工程, 2020, 48(3): 148-154.
[14] 刘也川, 张松, 谭俊哲, 关锰, 陶邵佳, 张春华. 机械滚压对A473M钢疲劳性能的影响[J]. 材料工程, 2020, 48(3): 163-169.
[15] 甘洪岩, 程明, 宋鸿武, 陈岩, 张士宏, Vladimir Petrenko. GH4169合金楔横轧加工过程中动态再结晶及织构演变[J]. 材料工程, 2020, 48(2): 114-122.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
地址:北京81信箱44分箱 邮政编码: 100095
电话:010-62496276 E-mail:matereng@biam.ac.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn