Please wait a minute...
 
材料工程  2013, Vol. 0 Issue (3): 71-76    DOI: 10.3969/j.issn.1001-4381.2013.03.014
  测试与表征 本期目录 | 过刊浏览 | 高级检索 |
C/C-SiC材料不同制动速率下的湿式摩擦磨损性能
李专, 肖鹏, 岳静, 熊翔
中南大学 粉末冶金国家重点实验,长沙 410083
Wet Friction and Wear Properties of C/C-SiC Composites During Different Braking Speeds
LI Zhuan, XIAO Peng, YUE Jing, XIONG Xiang
State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China
全文: PDF(4429 KB)   HTML()
输出: BibTeX | EndNote (RIS)      
摘要 以炭纤维针刺毡为预制体,先采用化学气相渗透法制备炭基体,然后采用熔融渗硅法制备SiC基体,得到C/C-SiC摩擦材料;利用MM-1000 型惯性试验台研究了C/C-SiC材料在不同制动速度下干态和CD15W-40柴油机油润滑状态下的摩擦磨损性能。研究结果表明:C/C-SiC摩擦材料与水的接触角为80.5°左右,为亲油性材料;C/C-SiC材料在CD15W-40柴油机油润滑状态下,随制动速度从3000r/min升高到6000r/min,其摩擦因数和线性磨损量在4000r/min时达到最大值,分别是0.21μm/cycle和1.1μm/cycle,而在5000r/min和6000r/min时,其摩擦因数均为0.17,线性磨损量均为0;C/C-SiC摩擦材料在湿态条件下能保持较高的摩擦因数,制动曲线平稳,磨损率低,可作为新一代工程机械和重型车辆湿式离合器用摩擦材料的候选材料。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
李专
肖鹏
岳静
熊翔
关键词 C/C-SiC湿式摩擦磨损炭纤维制动速度    
Abstract:Carbon fibre reinforced carbon and silicon carbide dual matrix composites (C/C-SiC) were fabricated by the combination of chemical vapor infiltration (CVI) with liquid silicon infiltration (LSI). The tribological behaviors of the C/C-SiC composite were investigated using an MM-1000 friction and wear tester, at different braking speeds under dry and machine oil lubricating conditions. The results indicate that the contact angle between C/C-SiC and distilled water is about 80.5°, which means the C/C-SiC are lipophilic materials. In the CD15W-40 diesel engine oil lubrication condition, with the brake speeds increasing from 3000r/min to 6000r/min, the coefficient of friction (COF) and linear wear of C/C-SiC reach the maximum value of 0.21μm/cycle and 1.1μm/cycle respectively, at 4000r/min. When the brake speeds are 5000r/min and 6000r/min, the COF and the linear wear are 0.17 and 0, respectively. C/C-SiC maintains a relatively high COF, smooth braking curves and lower wear rate in wet conditions, which can be used as candidate materials for wet clutch of new generation of construction machinery and heavy vehicles.
Key wordsC/C-SiC    wet condition    friction behavior    carbon fibre    braking speed
收稿日期: 2012-09-20      出版日期: 2013-03-20
中图分类号:  TB331  
  TH117.3  
基金资助:国家自然科学基金(51072231,51205417);中国博士后科学基金(20110491278);中央高校青年教师助推基金(2011QNZT43)
作者简介: 李专(1982-),男,在站博士后,中南大学材料科学与工程博士后流动站,主要研究高性能陶瓷基摩擦材料,联系地址:中南大学粉末冶金国家重点实验室(410083),E-mail:li_zhuan@yahoo.com.Cn
引用本文:   
李专, 肖鹏, 岳静, 熊翔. C/C-SiC材料不同制动速率下的湿式摩擦磨损性能[J]. 材料工程, 2013, 0(3): 71-76.
LI Zhuan, XIAO Peng, YUE Jing, XIONG Xiang. Wet Friction and Wear Properties of C/C-SiC Composites During Different Braking Speeds. Journal of Materials Engineering, 2013, 0(3): 71-76.
链接本文:  
http://jme.biam.ac.cn/CN/10.3969/j.issn.1001-4381.2013.03.014      或      http://jme.biam.ac.cn/CN/Y2013/V0/I3/71
[1] 王秀飞. 坦克离合器用C/C-SiC复合材料的制备及其性能研究. 长沙: 中南大学粉末冶金研究院, 2007.20-25.
[2] LIOYD F, DIPINO M A. Advances in wet friction materials 75 years of progress[J]. SAE Paper, 1980, 800977: 3088-3096.
[3] 林荣会, 孙平, 方亮. 重型汽车用湿式无石棉纸基摩擦材料研究[J] . 非金属矿, 2003, 26(5):54-55.LIN Rong-hui, SUN Ping, FANG Liang. Study on wet non-asbestos paper-based friction material for heavy vehicle[J] . Non-metallic Mines, 2003, 26(5):54-55.
[4] 蔡丹, 魏宸官, 宋文悦. 湿式摩擦离合器片翘曲变形研究[J].北京理工大学学报, 2000, 20(4): 449-451.CAI Dan, WEI Chen-guan, SONG Wen-yue. Friction discs distortion phenomena in wet clutch [J]. Journal of Beijing Institute of Technology, 2000, 20(4): 449-451.
[5] 叶世学. 铁铜基湿式烧结摩擦材料[J] . 粉末冶金技术, 1995, 11(4): 282-284.YE Shi-xue. Investigation of iron-copper based wet type sintered friction materials[J] . Powder Metallurgy Technology, 1995, 11 (4) : 282-284.
[6] KRENKEL W, HEIDENREICH B, RENZ R. C/C-SiC Composites for advanced friction systems[J].Advanced Engineering Materials, 2002, 4 (8):427-436.
[7] 李专. C/C-SiC摩擦材料的制备、结构和性能 . 长沙: 中南大学粉末冶金研究院, 2010.95-103.
[8] NASLAIN R. Design, preparation and properties of non-oxide CMCs for application in engines and nuclear reactors: an overview [J]. Composites Science and Technology, 2004, 64: 155-170.
[9] 范尚武 , 张立同, 成来飞. 三维针刺C/ SiC刹车材料的热物理性能[J].复合材料学报, 2011, 28(3):56-62. FAN Shang-wu, ZHANG Li-tong, CHENG Lai-fei. Thermal physical properties of 3D needled C/ SiC brake materials[J], Acta Materiae Compositae Sinica,2011, 28(3):56-62.
[10] 田广来, 徐永东, 范尚武, 等. 高性能碳/碳化硅刹车材料及其优化设计[J]. 复合材料学报, 2008, 25(2): 101-108. TIAN Guang-lai, XU Yong-dong, FAN Shang-wu, et al. High performance C/SiC brake materials and optimizing design [J] .Acta Materiae Compositae Sinica, 2008, 25(2):101-108.
[1] 元云岗, 康嘉杰, 岳文, 付志强, 朱丽娜, 佘丁顺, 王成彪. 不同温度下等离子渗氮后TC4钛合金的摩擦磨损性能[J]. 材料工程, 2020, 48(2): 156-162.
[2] 张军, 刘崇宇. 粉末冶金法制备CNT和SiC混杂增强铝基复合材料的摩擦磨损性能[J]. 材料工程, 2020, 48(11): 131-139.
[3] 马明星, 王志新, 梁存, 周家臣, 张德良, 朱达川. CeO2掺杂对AlCoCrCuFe高熵合金的组织结构与摩擦磨损性能的影响[J]. 材料工程, 2019, 47(7): 106-111.
[4] 陈海龙, 杨学锋, 王守仁, 鹿重阳, 吴元博. 改性酚醛树脂陶瓷摩擦材料的摩擦磨损性能[J]. 材料工程, 2019, 47(6): 108-113.
[5] 王勇刚, 刘和剑, 回丽, 职山杰, 刘海青. 激光熔覆原位自生碳化物增强自润滑耐磨复合涂层的高温摩擦学性能[J]. 材料工程, 2019, 47(5): 72-78.
[6] 黄凯, 蒋日鹏, 李晓谦, 李瑞卿, 张立华. 超声外场对原位TiB2/2A14铝基复合材料的摩擦磨损性能的影响[J]. 材料工程, 2019, 47(12): 78-84.
[7] 田晋, 高立, 蔡滨, 齐泽昊, 谭业发. 功能化纳米SiO2改性环氧树脂复合材料及其摩擦磨损行为与机制[J]. 材料工程, 2019, 47(11): 92-99.
[8] 江泽琦, 冯彦寒, 方建华, 刘坪, 陈波水, 谷科城, 吴江. 含硫代磷酸铵盐润滑油在电磁场作用下的摩擦学性能[J]. 材料工程, 2018, 46(9): 95-100.
[9] 杨伟华, 吴玉萍, 洪晟, 李佳荟, 李柏涛. 超音速火焰喷涂WC-10Co-4Cr涂层的微观组织与摩擦磨损性能[J]. 材料工程, 2018, 46(5): 120-125.
[10] 刘小辉, 王帅星, 杜楠, 赵晴, 康佳, 刘欢欢. 电解液中Na2WO4对Ti2AlNb微弧氧化膜结构及摩擦磨损性能的影响[J]. 材料工程, 2018, 46(2): 84-92.
[11] 刘用, 马胜国, 刘英杰, 张腾, 杨慧君. AlxCrCuFeNi2多主元高熵合金的摩擦磨损性能[J]. 材料工程, 2018, 46(2): 99-104.
[12] 樊振中, 熊艳才, 陆政, 孙刚, 王胜强. Al-7Sn-1.1Ni-Cu-0.2Ti轴承合金微观组织与力学性能[J]. 材料工程, 2017, 45(6): 8-16.
[13] 金小越, 吴杰, 杨璇, 王彬, 陈琳, 曲尧, 薛文斌. 槽电压对纯铁表面液相等离子体电解硼碳氮三元共渗层摩擦磨损性能的影响[J]. 材料工程, 2017, 45(4): 58-64.
[14] 王恩青, 岳建岭, 李淼磊, 李栋, 黄峰. Si含量对VAlSiN涂层微结构、力学性能和摩擦磨损性能的影响[J]. 材料工程, 2017, 45(4): 70-76.
[15] 王铁钢, 李柏松, 阎兵, 范其香, 刘艳梅, 宫骏, 孙超. 爆炸喷涂WC-Co/MoS2-Ni多层复合自润滑涂层的摩擦学行为[J]. 材料工程, 2017, 45(3): 73-79.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
地址:北京81信箱44分箱 邮政编码: 100095
电话:010-62496276 E-mail:matereng@biam.ac.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn