Please wait a minute...
 
材料工程  2015, Vol. 43 Issue (9): 19-24    DOI: 10.11868/j.issn.1001-4381.2015.09.004
  材料与工艺 本期目录 | 过刊浏览 | 高级检索 |
球磨制备轴承珠表面自润滑涂层及其摩擦性能
谭英梅1, 曹国剑1, 李双1, 古乐2
1. 哈尔滨理工大学 材料科学与工程学院, 哈尔滨 150040;
2. 哈尔滨工业大学 机电工程学院, 哈尔滨 150001
Preparation and Friction Properties of Self-lubricating Layer on Bearing Balls by Ball Milling
TAN Ying-mei1, CAO Guo-jian1, LI Shuang1, GU Le2
1. School of Materials Science and Engineering, Harbin University of Science and Technology, Harbin 150040, China;
2. School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001, China
全文: PDF(6448 KB)   HTML()
输出: BibTeX | EndNote (RIS)      
摘要 通过将MoS2粉末和轴承珠放入真空球磨罐中进行球磨的方法在轴承珠表面制备自润滑涂层。固定球磨转速为200r/min,研究不同球磨时间对轴承珠表面制备涂层的影响。采用配有能谱的扫描电子显微镜对球磨不同时间所制备涂层的形貌及元素分布进行观察。结果表明:随球磨时间的延长,涂层表面形貌变化不大,涂层厚度先增加后减小,Mo的分布先均匀后分散,球磨5h后涂层的厚度及元素的均匀性最佳。制备涂层的摩擦测试结果表明:球磨1h和5h所制备的涂层具有明显的润滑效果,而球磨10h的润滑效果不明显。球磨5h所制备的涂层具有最佳的润滑效果。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
谭英梅
曹国剑
李双
古乐
关键词 轴承珠二硫化钼行星式球磨摩擦    
Abstract:A self-lubricating layer on bearing balls was fabricated by ball milling of MoS2 powder in a vacuum container with bearing balls. The influence of ball milling time on the self-lubricating layer at the rotation speed of 200r/min was investigated. The morphology and elements distribution of the self-lubricating layers under different ball milling time were observed using the scanning electron microscope and EDS spectrum analysis.The results show that with ball milling time, the coating surface morphology changes little, thickness of the lubricating layer increases firstly and then decreases, Mo is distributed first evenly and then dispersely. Thickness and uniformity of element in the coating surface after ball milling for 5h are the best. The friction test results of the coatings show that lubricating effect is obvious with the ball milling for 1h and 5h while the lubricating effect is not obvious with ball milling for 10h. The self-lubricating layer fabricated by the ball milling for 5h has the best lubricating effect.
Key wordsbearing ball    MoS2    planetary ball milling    friction
收稿日期: 2014-03-26      出版日期: 2015-09-26
中图分类号:  TB43  
通讯作者: 古乐(1974-),男,教授,主要从事金属材料摩擦磨损方面研究工作,联系地址:黑龙江省哈尔滨市南岗区西大直街92号哈尔滨工业大学机械学院(150001),E-mail:ggggroup@163.com     E-mail: ggggroup@163.com
引用本文:   
谭英梅, 曹国剑, 李双, 古乐. 球磨制备轴承珠表面自润滑涂层及其摩擦性能[J]. 材料工程, 2015, 43(9): 19-24.
TAN Ying-mei, CAO Guo-jian, LI Shuang, GU Le. Preparation and Friction Properties of Self-lubricating Layer on Bearing Balls by Ball Milling. Journal of Materials Engineering, 2015, 43(9): 19-24.
链接本文:  
http://jme.biam.ac.cn/CN/10.11868/j.issn.1001-4381.2015.09.004      或      http://jme.biam.ac.cn/CN/Y2015/V43/I9/19
[1] CAO Y X, DU L Z, HUANG C B, et al.Wear behavior of sintered hexagonal boron nitride under atmosphere and water vapor ambiences[J]. Applied Surface Science, 2011, 257(23): 10195-10200.
[2] ZHU S Y, BI Q L, YANG J, et al. Influence of Cr content on tribological properties of Ni3Al matrix high temperature self-lubricating composites[J]. Tribology International, 2011, 44(10): 1182-1187.
[3] 潘国梁, 乔红斌, 郭强. 复合型固体润滑膜的滚动/滑动复合干磨损特性[J]. 哈尔滨工业大学学报, 2006, 38(增刊): 298-302. PAN Guo-liang, QIAO Hong-bin, GUO Qiang. Dry rolling/sliding wear characteristics of solid lubricating composite films[J]. Journal of Harbin Institute of Technology,2006,38(Suppl):298-302.
[4] 乔红斌, 郭强, 潘国梁,等. 粉末涂料固体润滑膜滚动/滑动复合干摩擦磨损特性研究[J]. 润滑与密封, 2006,(3): 47-49. QIAO Hong-bin, GUO Qiang, PAN Guo-liang,et al. Friction and wear characteristics of the polymer powder coatings for solid lubrication under the dry rolling/sliding condition[J]. Lubrication Engineering, 2006,(3): 47-49.
[5] 陈建敏,冶银平,党鸿辛.粘结固体润滑膜及其应用[J].摩擦学报,1994,14(2):180-189. CHEN Jian-min, YE Yin-ping, DANG Hong-xin. Developing situation and application of bonded solid lubricant films[J]. Tribology, 1994, 14(2): 180-189.
[6] 严晓华, 陈国需. 固体润滑技术的研究现状及展望[J]. 能源研究与信息, 2005, 21(2): 69-73. YAN Xiao-hua, CHEN Guo-xu. Current development and future prospects on solid lubricating techniques[J].Energy Research and Information, 2005, 21(2): 69-73.
[7] 罗军,王运动,蔡振兵,等.粘结MoS2固体润滑涂层的转动微动磨损特性[J].机械工程学报,2012,48(17):100-105. LUO Jun,WANG Yun-dong,CAI Zhen-bing,et al.Rotational fretting wear characteristics of bonded molybdenum disulfide solid lubrication coating[J].Journal of Mechanical Engineering,2012,48(17):100-105.
[8] 王小静,邵红红,王季.射频磁控溅射法制备MoS2/SiC双层薄膜[J].机械工程材料,2012,36(2):68-71. WANG Xiao-jing,SHAO Hong-hong,WANG Ji.MoS2/SiC double films prepared by radio frequency magnetron sputtering[J]. Materials for Mechanical Engineering,2012,36(2):68-71.
[9] YANG J, LUO J B, PANG S Q. Effect of Ti or TiN codeposition on the performance of MoS2 based composite coatings[J]. Thin Solid Films, 2004, 461(2): 288-293.
[10] 高名传,童向阳,汪洪生.热喷涂法制备钼系涂层的研究进展[J].中国钼业,2014,38(6):41-47. GAO Ming-chuan,TONG Xiang-yang,WANG Hong-sheng.Research progress of Mo-based coatings fabricated by thermal spray technology[J].China Molybdenum Industry,2014,38(6):41-47.
[11] WEI R H, YANG H B, DU K, et al.Preparation of type-ⅡMoS2 film by chemical bath deposition onto Si coated with electrolessly Ni[J]. Materials Science and Engineering: B, 2007, 138(3): 259-262.
[12] SPALVINS T. Coatings for wear and lubrication[J]. Thin Solid Films,1978,53:285-300.
[13] 赵学敏,汪刘应,张虎,等.固体润滑涂层研究工艺的研究进展[J].材料导报,2013,27(22):68-71. ZHAO Xue-min,WANG Liu-ying,ZHANG Hu,et al.Research progress on the preparation of solid lubricating coatings[J].Materials Review,2013,27(22):68-71.
[14] 刘政军,冯丽峰,成明华,等.材料表面改性技术原理分析[J].现代焊接,2008,(8):21-25. LIU Zheng-jun,FENG Li-feng,CHENG Ming-hua,et al.Brief analysis of the principle of material surface modification technology[J].Modern Welding Technology,2008,(8):21-25.
[15] YOSHIDA H,LU Y,NAKAYAMA H,et al. Fabrication of TiO2 film by mechanical coating technique and its photocatalytic activity[J]. Journal of Alloys and Compounds,2009,475(1-2):383-386.
[16] HAO L, LU Y, SATO H, et al.Fabrication of zinc coatings on alumina balls from zinc powder by mechanical coating technique and the process analysis[J]. Powder Technology,2012,228:377-384.
[17] HAO L, LU Y,HIROSHI A, et al.The influence of the processing parameters on the formation of iron thin films on alumina balls by mechanical coating technique[J]. Journal of Materials Processing Technology,2012,212(5):1169-1176.
[18] LU Y, YOSHIDA H, NAKAYAMA H, et al. Formation of TiO2/Ti composite photocatalyst film by 2-step mechanical coating technique[J]. Materials Science Forum,2011,675-677:1229-1232.
[19] ROSENKRANZ S, BREITUNG-FAES S, KWADE A.Experimental investigations and modeling of the ball motion in planetary ball mills[J]. Powder Technology,2011, 212(1): 224-230.
[20] ERDEM A S, ERGÜN S L.The effect of ball size on breakage rate parameter in a pilot scale ball mill[J]. Minerals Engineering, 2009, 22(7-8): 660-664.
[21] GU L, CAO G J, WANG L Q, et al. Synthesis and characterization of a self-lubricating film on bearing balls[J]. Advanced Materials Research, 2011,154-155: 367-370.
[22] 韦习成, 赵源. FeS层的减磨耐磨机理[J]. 润滑与密封, 1994,(2): 12-17. WEI Xi-cheng, ZHAO Yuan. Anti-friction and wear resistance mechanism of FeS layer[J]. Lubrication Engineering, 1994,(2): 12-17.
[23] 赵军军, 张平, 韩文政. 离子渗硫技术在装甲车辆中的应用[J]. 装甲兵工程学院学报, 2003, 17(1): 10-14. ZHAO Jun-jun, ZHANG Ping, HAN Wen-zheng. The application of ion sulphidizing process to armored vehicle[J]. Journal of Armored Force Engineering Institute, 2003, 17(1): 10-14.
[24] 王海斗, 徐滨士, 刘家浚,等. 两步法制备固体润滑FeS薄膜的摩擦磨损性能研究[J].摩擦学学报, 2005, 25(4):304-306. WANG Hai-dou, XU Bin-shi, LIU Jia-jun,et al. Study on the tribological properties of FeS solid lubrication films prepared by two-step method[J]. Tribology, 2005, 25(4):304-306.
[1] 徐晨曦, 胡安俊, 舒朝著, 龙剑平. 金属相二硫化钼在能量储存与转化中的应用进展[J]. 材料工程, 2020, 48(9): 34-46.
[2] 叶锦宗, 李锦棒, 周宁宁, 曹均, 卿涛, 蒋世宇, 于爱兵. 成型工艺对多孔PI材料摩擦学及力学性能的影响[J]. 材料工程, 2020, 48(9): 144-151.
[3] 尹艳丽, 于鹤龙, 周新远, 宋占永, 王红美, 王文宇, 刘晓亭, 徐滨士. 基于正交实验方法的蛇纹石润滑油添加剂摩擦学性能[J]. 材料工程, 2020, 48(7): 146-153.
[4] 赵强, 祝文卉, 邵天巍, 帅焱林, 刘佳涛, 王冉, 张利, 梁晓波. Ti-22Al-25Nb合金惯性摩擦焊接头显微组织与力学性能[J]. 材料工程, 2020, 48(6): 140-147.
[5] 张传香, 陈亚玲, 巩云, 刘慧颖, 戴玉明, 丛园. 二硫化钼/石墨烯复合材料的一步水热合成及电催化性能[J]. 材料工程, 2020, 48(5): 56-61.
[6] 白明洁, 刘金龙, 齐志娜, 何江, 魏俊俊, 苗建印, 李成明. 石墨烯纳米流体研究进展[J]. 材料工程, 2020, 48(4): 46-59.
[7] 邓运来, 邓舒浩, 叶凌英, 林森, 孙琳, 吉华. 焊后热处理对AA7204-T4铝合金搅拌摩擦焊接头组织与力学性能的影响[J]. 材料工程, 2020, 48(4): 131-138.
[8] 谢红梅, 蒋斌, 戴甲洪, 唐昌平, 李权, 潘复生. 石墨烯和氧化石墨烯水基润滑添加剂在镁合金冷轧中的摩擦学行为[J]. 材料工程, 2020, 48(3): 66-74.
[9] 元云岗, 康嘉杰, 岳文, 付志强, 朱丽娜, 佘丁顺, 王成彪. 不同温度下等离子渗氮后TC4钛合金的摩擦磨损性能[J]. 材料工程, 2020, 48(2): 156-162.
[10] 张军, 刘崇宇. 粉末冶金法制备CNT和SiC混杂增强铝基复合材料的摩擦磨损性能[J]. 材料工程, 2020, 48(11): 131-139.
[11] 李新星, 王红侠, 施剑峰, 韩伯群. TC11钛合金表面保护性摩擦氧化层的形成及作用[J]. 材料工程, 2020, 48(10): 141-147.
[12] 李春华, 王晗, 郝海. AZ91及AZ91-Y合金复合干摩擦性能的对比[J]. 材料工程, 2020, 48(1): 108-114.
[13] 李晓红, 张彦华, 李赞, 李菊, 张田仓. 热处理温度对TC17(α+β)/TC17(β)钛合金线性摩擦焊接头组织及力学性能的影响[J]. 材料工程, 2020, 48(1): 115-120.
[14] 赵梓钧, 杨新岐, 李胜利, 李冬晓. 工具形状及工艺过程对搅拌摩擦增材成形及缺陷的影响[J]. 材料工程, 2019, 47(9): 84-92.
[15] 马明星, 王志新, 梁存, 周家臣, 张德良, 朱达川. CeO2掺杂对AlCoCrCuFe高熵合金的组织结构与摩擦磨损性能的影响[J]. 材料工程, 2019, 47(7): 106-111.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
版权所有 © 2015《材料工程》编辑部
地址:北京81信箱44分箱 邮政编码: 100095
电话:010-62496276 E-mail:matereng@biam.ac.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn