Abstract:Near-isothermal canned forging for molybdenum powder sinter was investigated by using finite element software. The influence of process parameters (temperature, friction coefficient and forging rate) on strain distribution was discussed. The results show that the average equivalent strain increases with the rising of forging temperature, but the corresponding deformation is non-uniform. Average equivalent strain increases with the increase of friction coefficient, meanwhile, the fracture crack easily occurs owing to non-uniform deformation. The effect of forging rate on strain is not obvious. Through analysis on the orthogonal experiment, the effect of temperature on deformation uniformatity is the most remarkable.
王宁, 李健, 关志军, 谭凯. 工艺参数对钼粉烧结体近等温包套锻造成形过程中应变的影响[J]. 材料工程, 2015, 43(6): 46-51.
WANG Ning, LI Jian, GUAN Zhi-jun, TAN Kai. Effect of Processing Parameters on Strain Distribution During Near-isothermal Canned Forging for Molybdenum Powder Sinter. Journal of Materials Engineering, 2015, 43(6): 46-51.
[1] OHSER-WIEDEMANN R, MARTIN U, SEIFERT H J, et al. Densification behaviour of pure molybdenum powder by spark plasma sintering[J].Refractory Metals & Hard Materials,2010,28(4):550-557.
[2] LEICHTFRIED GSCHNEIBEL J H, HEILMAIER M. Ductility and impact resistance of powder-metallurgical molybdenum-rhenium alloys[J].Physical Metallurgy and Materials Science,2006,37(10):2955-2961.
[3] SINGH S, JHA A K, KUNAR S. Upper bound analysis and experimental investigations of dynamic effects during sinter-forging of irregular polygonal performs[J].Materials Processing Technology, 2007,194(1):134-144.
[4] HUANG Cheng-chao, CHENG Jung-ho. Forging simulation of sintered powder compacts under various frictional conditions[J]. Mechanical Sciences,2002,44(3):489-507.
[5] SHANMUGASUNDARAM D, CHANDRAMOULI R. Tensile and impact behavior of sinter-forged Cr, Ni and Mo alloyed powder metallurgy steels[J].Materials & Design,2009,30(9):3444-3449.
[6] 华林,毛华杰,赵仲治.粉末冶金锻造变形力和密度计算[J].粉末冶金工业,2010,10(1):26-31.HUANG Lin, MAO Hua-jie, ZHAO Zhong-zhi. Calculation of pressure and densification for powder forging[J].Powder Metallurgical Industry,2010,10(1):26-31.
[7] 周灿栋,蒋国昌,朱钰如.粉末锻造制备含氮奥氏体不锈钢[J].粉末冶金技术,2004,22(1):41-44.ZHOU Can-dong, JIANG Guo-chang, ZHU Yu-ru. Production of nitrogenous austenitic stainless steel by powder forging[J].Powder Metallurgy Technology,2004,22(1):41-44.
[8] 王川.TiAl基合金板材制备与组织性能研究[D].哈尔滨:哈尔滨工业大学,2007.WANG Chuan. Preparation, microstructure and mechanical properties of TiAl based alloy sheet[D].Harbin: Harbin Institute of Technology,2007.
[9] 张宏亮.粉末冶金钼管热挤压工艺基础研究[D].太原:太原理工大学,2010.ZHANG Hong-liang. The fundamental research of hot extrusion process for powder metallurgy molybdenum tube[D].Taiyuan: Taiyuan University of Technology,2010.
[10] 赵传涛.非致密体钼的热压扭成形数值模拟[D].合肥:合肥工业大学,2008. ZHAO Chuan-tao. Numerical simulation of hot torsion and compression of porous molybdenum[D].Hefei: Hefei University of Technology,2008.
[11] 薛克敏,王晓溪,李萍,等.纯钼粉多孔烧结材料ECAP的数值模拟及实验[J].中国有色金属学报,2011,21(1):32-37. XUE Ke-min, WANG Xiao-xi, LI Ping, et al. Numerical simulation study of ECAP on sintered power molybdenum materials[J].Transactions of Nonferrous Metals Society of China,2011,21(1): 32-37.
[12] HONG Shen-ze, WANG Shu-jun, CAI Ke-yu. Thermo dynamic couple numerical simulation of the temperature field in hot forging forming process[J].Materials Processing Technology, 2009,41(12):1120-1125.
[13] 罗文波,胡云贵,胡自化.圆柱平板间镦粗的热力分析[J].塑性工程学报,2000,7(1):64-68. LUO Wen-bo, HU Yun-gui, HU Zi-hua. Thermo chemical analysis of upsetting of cylindrical billet between rough plate dies [J].Plasticity Engineering,2000,7(1):64-68.
[14] 李萍,薛克敏,吕炎.Ti-15-3合金反挤压成形的热力耦合模拟[J].中国有色金属学报,2002,12(3):578-581. LI Ping, XUE Ke-min, LU Yan. Numerical simulation of coupled thermo-mechanical behavior of Ti-15-3 alloy during back-extrusion[J].Transactions of Nonferrous Metals Society of China,2002,12(3):578-581.
[15] CHO J R, YOO Y S, JEONG H S. The Al powder process: its finite analysis[J].Materials Processing Technology,2001,111:204-209.