Abstract:In order to further enhance the performance of the AlSi10Mg parts fabricated by selective laser melting, the WC/AlSi10Mg composite with 0.1%WC(mass fraction) was obtained by mixing the nano-WC and AlSi10Mg in mixing machine, and the specimen block was fabricated by the selective laser melting machine. By comparing the AlSi10Mg specimens fabricated by the same process, the effects of nano-WC on the microstructure formation and evolution of the microstructure and the mechanical properties of the microstructure were investigated. The results show that the WC/AlSi10Mg powder has good sphericity and the particle size distribution is concentrated in 20-60 μm. The WC/AlSi10Mg sample has the density of over 99% and hardness of about 158.89HV, which is 14.58% higher than that of the AlSi10Mg sample. The WC/AlSi10Mg samples grow uniformly and densely, with obvious molten pool lines. The inside of the crystal grain is α-Al matrix, and the boundary is a eutectic Si phase interposed with WC. The yield strength of the WC/AlSi10Mg sample reaches 337.75 MPa, the ultimate strength is as high as 514.00 MPa, and the elongation is 3.78%. Compared with the same process, AlSi10Mg samples are increased by 4.73%, 6.25% and 35.97%, respectively. Therefore, SLM-processed WC/AlSi10Mg composite parts have better application prospects than AlSi10Mg parts.
[1] 杨平华,高祥熙,梁菁,等. 金属增材制造技术发展动向及无损检测研究进展[J]. 材料工程, 2017, 45(9):13-21. YANG P H, GAO X X, LIANG J, et al. Development trend and NDT progress of metal additive manufacture technique[J]. Journal of Materials Engineering, 2017, 45(9):13-21.
[2] 王延庆,沈竞兴,吴海全. 3D打印材料应用和研究现状[J]. 航空材料学报, 2016, 36(4):89-98. WANG Y Q, SHEN J X, WU H Q. Application and research status of alternative materials for 3D-printing technology[J]. Journal of Aeronautical Materials, 2016, 36(4):89-98.
[3] CALIGNANO F. Design optimization of supports for overhanging structures in aluminum and titanium alloys by selective laser melting[J]. Materials & Design, 2014, 64:203-213.
[4] HU Z H, ZHU H H, ZHANG H, et al. Experimental investigation on selective laser melting of 17-4PH stainless steel[J]. Optics & Laser Technology, 2017, 87:17-25.
[5] TJONG S C. Novel nanoparticle-reinforced metal matrix composites with enhanced mechanical properties[J]. Advanced Engineering Materials, 2010, 9(8):639-652.
[6] KUMAR S S, BAI V S, RAJKUMAR K V, et al. Elastic modulus of Al-Si/SiC metal matrix composites as a function of volume fraction[J]. Journal of Physics D:Applied Physics, 2009, 42(42):175504.
[7] KUMAR S S, BAI V S, RAJASEKHARAN T. Aluminium matrix composites by pressureless infiltration:the metallurgical and physical properties[J]. Journal of Physics D:Applied Physics, 2008, 41(10):105403.
[8] WEI P, WEI Z, CHEN Z, et al. The AlSi10Mg samples produced by selective laser melting:single track, densification, microstructure and mechanical behavior[J]. Applied Surface Science, 2017,408:38-50.
[9] LEVY G N, SCHINDEL R, KRUTH J P. Rapid manufacturing and rapid tooling with layer manufacturing (LM) technologies, state of the art and future perspectives[J]. CIRP Annals, 2003, 52(2):589-609.
[10] WU J, WANG X Q, WANG W, et al. Microstructure and strength of selectively laser melted AlSi10Mg[J]. Acta Materialia, 2016, 117:311-320.
[11] READ N, WANG W, ESSA K, et al. Selective laser melting of AlSi10Mg alloy:process optimisation and mechanical properties development[J]. Materials & Design, 2015, 65:417-424.
[12] LOUVIS E, FOX P, SUTCLIFFE C J. Selective laser melting of aluminium components[J]. Journal of Materials Processing Technology, 2011, 211(2):275-284.
[13] PRASHANTH K G, SCUDINO S, KLAUSS H J, et al. Microstructure and mechanical properties of Al-12Si produced by selective laser melting:effect of heat treatment[J]. Materials Science and Engineering:A, 2014, 590:153-160.
[14] LAM L P, ZHANG D Q, LIU Z H, et al. Phase analysis and microstructure characterisation of AlSi10Mg parts produced by selective laser melting[J]. Virtual & Physical Prototyping, 2015, 10(4):207-215.
[15] 林英华,陈志勇,李月华,等. TC4钛合金表面激光熔覆原位制备TiB陶瓷涂层的微观组织特征与硬度特性[J]. 红外与激光工程, 2012, 41(10):2694-2698. LIN Y H, CHEN Z Y, LI Y H, et al. Microstructure and hardness properties of in-situ TiB ceramic coatings prepared by laser cladding on TC4 titanium alloy[J].Infrared and Laser Engineering,2012,41(10):2694-2698.
[16] 赵龙志, 杨敏. 颗粒增强铝基复合材料的研究[J]. 热加工工艺, 2011, 40(20):107-110. ZHAO L Z, YANG M. Aluminum matrix composites particle reinforced[J]. Thermal processing technology, 2011, 40(20):107-110.
[17] 杨胶溪,胡星,王艳芳. TC轴承激光增材制造工艺及组织性能研究[J]. 材料工程, 2016, 44(7):61-66. YANG J X, HU X, WANG Y F. Microstructure and properties of laser additive manufacturing TC bearing[J]. Journal of Materials Engineering, 2016, 44(7):61-66.
[18] ABOULKHAIR N T, MASKERY I, et al. On the formation of AlSi10Mg single tracks and layers in selective laser melting:Microstructure and nano-mechanical properties[J]. Journal of Materials Processing Technology, 2016, 230:88-98.
[19] 张文奇,朱海红,胡志恒,等. AlSi10Mg的激光选区熔化成形研究[J]. 金属学报, 2017, 53(8):918-926. ZHANG W Q, ZHU H H, HU Z H, et al. Study on laser selective melting forming of AlSi10Mg[J]. Acta Metallurgica Sinica, 2017, 53(8):918-926.
[20] LOUVIS E, FOX P, SUTCLIFFE C J. Selective laser melting of aluminium components[J]. Journal of Materials Processing Technology, 2011, 211(2):275-284.
[21] LI Y, GU D. Parametric analysis of thermal behavior during selective laser melting additive manufacturing of aluminum alloy powder[J]. Materials & Design, 2014, 63:856-867.
[22] LI B, WANG H, JIE J, et al. Effects of yttrium and heat treatment on the microstructure and tensile properties of Al-7.5Si-0.5Mg alloy[J]. Materials & Design, 2011, 32(3):1617-1622.
[23] 邹章雄,项金钟,许思勇. Hall-Petch关系的理论推导及其适用范围讨论[J]. 物理测试, 2012, 30(6):13-17. ZOU Z X, XIANG J Z, XU S Y. Theoretical derivation of Hall-Petch relationship and discussion of its applicable range[J]. Physical Test, 2012, 30(6):13-17.
[24] VO N Q, DUNAND D C, SEIDMAN D N. Improving aging and creep resistance in a dilute Al-Sc alloy by microalloying with Si, Zr and Er[J]. Acta Materialia, 2014, 63:73-85.