Please wait a minute...
 
材料工程  2017, Vol. 45 Issue (1): 27-32    DOI: 10.11868/j.issn.1001-4381.2014.001258
  研究论文 本期目录 | 过刊浏览 | 高级检索 |
激光快速成形GH4169合金显微组织与力学性能
杜博睿, 张学军, 郭绍庆, 李能, 孙兵兵, 唐思熠
北京航空材料研究院 3D打印研究与 工程技术中心, 北京 100095
Microstructure and Mechanical Properties of Laser Melting Deposited GH4169 Superalloy
DU Bo-rui, ZHANG Xue-jun, GUO Shao-qing, LI Neng, SUN Bing-bing, TANG Si-yi
3D Printing Research and Engineering Technology Center, Beijing Institute of Aeronautical Materials, Beijing 100095, China
全文: PDF(986 KB)   HTML()
输出: BibTeX | EndNote (RIS)      
摘要 利用GH4169合金粉末进行激光快速成形实验,制备出GH4169合金块状试样,并进行固溶时效热处理。利用扫描电镜(SEM)及能谱分析(EDS)等方法分别对激光成形沉积态及固溶时效态试样进行显微组织及元素偏析分析,并测试显微硬度、室温及高温拉伸性能。结果表明:沉积态微观组织为生长方向不一的细长柱状树枝晶,组织细小致密;经过固溶时效热处理后晶粒得到细化,晶粒内部仍保留枝晶亚结构;固溶时效态试样较沉积态显微硬度及抗拉强度大幅提高,塑性有所下降,但整体优于锻件技术标准。断口形貌表现为韧性穿晶断裂方式。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
杜博睿
张学军
郭绍庆
李能
孙兵兵
唐思熠
关键词 激光快速成形GH4169显微组织力学性能    
Abstract:The block samples of a Ni-based superalloy named GH4169 were prepared by laser melting deposited method using the corresponding GH4169 alloy powders,and then were heat treated with solution treatment followed by double aging.The microstructure and element segregation analysis of both as-deposited and heat treated samples were studied by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).The microhardness as well as tensile properties at room and elevated temperatures were tested.The results indicate that the microstructure of as-deposited sample mainly consists of columnar dendritic crystals that grow along with different directions.Grains are refined after solution and aging heat treatment,but remain dendritic crystals substructure inside.Compared with the as-deposited sample,the microhardness and tensile strength of the heat treated sample increase substantially,but the plasticity somewhat decreases.Nonetheless the tensile properties are superior to the standard values of forgings.The fracture surface exhibits ductile transcrystalline fracture mode.
Key wordslaser melting deposition    GH4169    microstructure    mechanical property
收稿日期: 2014-05-23      出版日期: 2017-01-19
中图分类号:  TG146.4  
通讯作者: 杜博睿(1988-),男,工程师,硕士,主要从事激光3D打印及焊接技术研究,联系地址:北京市81信箱20分箱(100095),E-mail:duborui621@126.com     E-mail: duborui621@126.com
引用本文:   
杜博睿, 张学军, 郭绍庆, 李能, 孙兵兵, 唐思熠. 激光快速成形GH4169合金显微组织与力学性能[J]. 材料工程, 2017, 45(1): 27-32.
DU Bo-rui, ZHANG Xue-jun, GUO Shao-qing, LI Neng, SUN Bing-bing, TANG Si-yi. Microstructure and Mechanical Properties of Laser Melting Deposited GH4169 Superalloy. Journal of Materials Engineering, 2017, 45(1): 27-32.
链接本文:  
http://jme.biam.ac.cn/CN/10.11868/j.issn.1001-4381.2014.001258      或      http://jme.biam.ac.cn/CN/Y2017/V45/I1/27
[1] LIN J, STEEN W M. Design characteristics and development of a nozzle for coaxial laser cladding[J]. Journal of Laser Applications, 1998, 10(2):55-64.
[2] 王华明,张凌云,李安,等.先进材料与高性能零件快速凝固激光加工研究进展[J].世界科技研究与发展,2004,26(3):27-31. WANG H M, ZHANG L Y, LI A, et al. Progress on rapid solidification laser processing for advanced materials and component[J]. World Sci-technol R&D, 2004, 26(3):27-31.
[3] 黄卫东, 林鑫. 激光立体成形高性能金属零件研究进展[J]. 中国材料进展, 2010, 29(6):12-27. HUANG W D, LIN X.Research progress in laser solid forming of high performance metallic component[J]. Materials China, 2010, 29(6):12-27.
[4] 王华明,张述泉,汤海波,等.大型钛合金结构激光快速成形技术研究进展[J]. 航空精密制造技术, 2008, 44(6):28-30. WANG H M, ZHANG S Q, TANG H B, et al. Research progress of laser melting deposition of large titanium structure components[J]. Aviation Precision Manufacturing Technology, 2008, 44(6):28-30.
[5] 王华明,张述泉,王向明.大型钛合金结构件激光直接制造的进展与挑战[J].中国激光,2009,36(12):3204-3210. WANG H M, ZHANG S Q, WANG X M. Progress and challenges of laser direct manufacturing of large titanium structure components[J]. Chinese Journal of Lasers, 2009, 36(12):3204-3209.
[6] 张学军, 唐思熠, 肇恒跃, 等. 3D打印技术研究现状和关键技术[J]. 材料工程, 2016, 44(2):122-128. ZHANG X J, TANG S Y, ZHAO H Y,et al.Research status and key technologies of 3D printing[J]. Journal of Materials Engineering, 2016, 44(2):122-128.
[7] 王会阳, 安云岐, 李承宇,等. 镍基高温合金材料的研究进展[J]. 材料导报, 2011,(增刊2):482-486. WANG H Y, AN Y Q, LI C Y, et al. Research progress of Ni-based superalloys[J]. Materials Review, 2011,(Suppl 2):482-486.
[8] SHYAM A, MILLIGAN W W. Effects of deformation behavior on fatigue fracture surface morphology in a nickel-base superalloy[J]. Acta Materialia, 2004, 52(6):1503-1513.
[9] GELL M, DUHL D N, GIAMEI A F. The development of single crystal superalloy turbine blades[A].Superalloys, 1980.205-214.
[10] 唐中杰, 郭铁明, 付迎,等. 镍基高温合金的研究现状与发展前景[J]. 金属世界, 2014,(1):36-40. TANG Z J, GUO T M, FU Y, et al. Research present station and the development prospect of nickel-based superalloy[J]. Metal World, 2014,(1):36-40.
[11] QI H, AZER M, RITTER A. Studies of standard heat treatment effects on microstructure and mechanical Properties of laser net shape manufactured Inconel 718[J]. Metallurgical and Materials Transactions A, 2009, 40(10):2410-2422.
[12] LI J, WANG H M. Microstructure and mechanical properties of rapid directionally solidified Ni-base superalloy Rene'41 by laser melting deposition manufacturing[J]. Materials Science and Engineering:A, 2010, 527:4823-4829.
[13] AMATO K N, GAYTAN S M, MURR L E, et al. Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting[J]. Acta Materialia, 2012, 60:2229-2239.
[14] 冯莉萍,黄卫东,林鑫,等.FGH95合金激光成形定向凝固显微组织与性能[J].中国有色金属学报,2003,13(1):181-187. FENG L P, HUANG W D, LIN X, et al. FGH95 superalloy laser metal forming directional solidification[J]. The Chinese Journal of Nonferrous Metals, 2003,13(1):181-187.
[15] 张霜银,林鑫,陈静,等.工艺参数对激光快速成形TC4钛合金组织及成形质量的影响[J].稀有金属材料与工程,2007,36(10):1839-1843. ZHANG S Y, LIN X, CHEN J, et al. Influence of processing parameter on the microstructure and forming characterizations of Ti-6Al-4V titanium alloy after laser rapid forming processing[J]. Rare Metal Materials and Engineering, 2007, 36(10):1839-1843.
[16] CHONG C E, WILCOX W R. Control of interface shape in the vertical bridgman-stockbarger technique[J]. J of Crystal Growth, 1974, 21:135-140.
[17] 庄景云,杜金辉.变形高温合金[M].北京:冶金工业出版社, 2006.
[18] 中国航空材料手册编辑委员会.中国航空材料手册:变形高温合金、铸造高温合金[M]. 2版.北京:中国标准出版社,2001. Editor Committee of Chinese Aerospace Material Manual.Chinese Aerospace Material Manual:Deforming Superalloy and Casting Superalloy[M]. 2nd Ed.Beijing:Standards Press of China, 2001.
[1] 杨旭东, 安涛, 邹田春, 巩天琛. 湿热环境对碳纤维增强树脂基复合材料力学性能的影响及其损伤机理[J]. 材料工程, 2019, 47(7): 84-91.
[2] 王聃, 陶德华, 黄秀玲, 华子恺. 聚甲基丙稀酸羟乙酯甘油凝胶仿软骨材料的制备与性能[J]. 材料工程, 2019, 47(7): 71-75.
[3] 刘文祎, 徐聪, 刘茂文, 肖文龙, 马朝利. 稀土元素Gd对Al-Si-Mg铸造合金微观组织和力学性能的影响[J]. 材料工程, 2019, 47(6): 129-135.
[4] 王飞云, 金建军, 江志华, 王晓震, 胡春文. 热处理温度对新型马氏体时效不锈钢微观组织和性能的影响[J]. 材料工程, 2019, 47(6): 152-160.
[5] 陈海龙, 杨学锋, 王守仁, 鹿重阳, 吴元博. 改性酚醛树脂陶瓷摩擦材料的摩擦磨损性能[J]. 材料工程, 2019, 47(6): 108-113.
[6] 闫钊鸣, 张治民, 杜玥, 张冠世, 任璐英. 均匀化处理对Mg-13Gd-3.5Y-2Zn-0.5Zr镁合金组织和力学性能的影响[J]. 材料工程, 2019, 47(5): 93-99.
[7] 薛子明, 雷卫宁, 王云强, 钱海峰, 李奇林. 超临界条件下脉冲占空比对石墨烯复合镀层微观结构和性能的影响[J]. 材料工程, 2019, 47(5): 53-62.
[8] 李惠, 肖文龙, 张艺镡, 马朝利. 多重结构Ti-B4C/Al2024复合材料的组织和力学性能[J]. 材料工程, 2019, 47(4): 152-159.
[9] 崔岩, 项俊帆, 曹雷刚, 杨越, 刘园. 碳化硅颗粒表面吸附质对铝基复合材料制备及力学性能的影响[J]. 材料工程, 2019, 47(4): 160-166.
[10] 李亚锋, 礼嵩明, 黑艳伟, 邢丽英, 陈祥宝. 太阳辐照对芳纶纤维及其复合材料性能的影响[J]. 材料工程, 2019, 47(4): 39-46.
[11] 赵双赞, 燕绍九, 陈翔, 洪起虎, 李秀辉, 戴圣龙. 石墨烯纳米片增强铝基复合材料的动态力学行为[J]. 材料工程, 2019, 47(3): 23-29.
[12] 宋仁国. 微弧氧化技术的发展及其应用[J]. 材料工程, 2019, 47(3): 50-62.
[13] 赵云松, 郭媛媛, 赵敬轩, 张晓铁, 刘砚飞, 杨岩, 姜华, 张剑, 骆宇时. 微量Hf对大角度晶界含Re双晶合金高温持久性能的影响[J]. 材料工程, 2019, 47(2): 76-83.
[14] 李灿, 陈文琳, 雷远. 微量Sr及均匀化工艺对Al-Mg-Si-Cu-Mn变形铝合金铸态组织与性能的影响[J]. 材料工程, 2019, 47(2): 90-98.
[15] 王宇, 熊柏青, 李志辉, 温凯, 黄树晖, 李锡武, 张永安. 新型超高强Al-Zn-Mg-Cu合金热压缩变形行为及微观组织特征[J]. 材料工程, 2019, 47(2): 99-106.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
版权所有 © 2015《材料工程》编辑部
地址:北京81信箱44分箱 邮政编码: 100095
电话:010-62496276 E-mail:matereng@biam.ac.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn